manualshive.com logo in svg

Suzuki SMD12, Operator'S Manual

The Suzuki SMD12 Operator's Manual is the essential companion for any Suzuki SMD12 owner. With easy-to-follow instructions and detailed diagrams, this manual guides users through every aspect of operating and maintaining their SMD12. Download it for free from our website now and unlock the full potential of your Suzuki SMD12.

Share
Download
background image

2.  ENGINE DISPLAY

2-8

2.2.3

How to edit the Engine display

The Engine displays are fully customizable. You can edit the displays as follows:

•  Remove the item from the display
•  Add the item to the display
•  Rearrange the item in the display
•  Rename the display
•  Delete the display
•  Remove the display
•  Add the custom display

Note: 

To restore the default Engine displays, go to the Home screen, then tap [Set-

tings] - [Initial Setup] - [Graphic Instruments Setup] - [Reset Instrument Pages]. All de-
fault displays are restored and any custom displays are deleted.

How to prepare for editing

To start the editing process, tap anywhere on the Engine display to show the pop-up 
menu, then tap [Edit Page] on the menu. A blue line circumscribes each item in the 
display, as shown in the figure below. Edit the display referring to the procedures in 
the coming sections. To save your changes, tap anywhere on the item display to show 
the pop-up menu, then tap [End Edit] on the menu.

How to rearrange the items in the Engine display

 Drag and drop the items to your liking.

Summary of Contents for SMD12



















































































































































































































































































































































Reviews:

No comments

Related manuals for SMD12

jablotron nanny Quick Start Manual preview
nanny
Brand: jablotron Pages: 2
Samsung SyncMaster 1200NF Instrucciones De Usuario preview
SyncMaster 1200NF
Brand: Samsung Pages: 30
Samsung SyncMaster 172W User Manual preview
SyncMaster 172W
Brand: Samsung Pages: 45
Samsung SyncMaster 2032GWPlus Owner'S Manual preview
SyncMaster 2032GWPlus
Brand: Samsung Pages: 62
Samsung SyncMaster 2033SN Manual Del Usuario preview
SyncMaster 2033SN
Brand: Samsung Pages: 91
Samsung SyncMaster 1100MB Manual preview
SyncMaster 1100MB
Brand: Samsung Pages: 62
Samsung SyncMaster 171B, 171S, 181B, 171T, 171Q User Manual preview
SyncMaster 171B, 171S, 181B, 171T, 171Q
Brand: Samsung Pages: 83
Samsung SyncMaster SM320MX-2 User Manual preview
SyncMaster SM320MX-2
Brand: Samsung Pages: 109
Samsung T200HD - SyncMaster - 20" LCD Monitor Guía De Inicio Rápido preview
T200HD - SyncMaster - 20" LCD Monitor
Brand: Samsung Pages: 27
Samsung SyncMaster TC180 Quick Setup Manual preview
SyncMaster TC180
Brand: Samsung Pages: 2
Samsung T220HD - SyncMaster - 22" LCD Monitor User Manual preview
T220HD - SyncMaster - 22" LCD Monitor
Brand: Samsung Pages: 88
Samsung UD55D User Manual preview
UD55D
Brand: Samsung Pages: 241
Samsung SyncMaster XL2270 User Manual preview
SyncMaster XL2270
Brand: Samsung Pages: 43
Samsung SyncMaster S24A460B User Manual preview
SyncMaster S24A460B
Brand: Samsung Pages: 44
Samsung SyncMaster S22A300N Manual Del Usuario preview
SyncMaster S22A300N
Brand: Samsung Pages: 48
Samsung SyncMaster S27A850D Manual Del Usuario preview
SyncMaster S27A850D
Brand: Samsung Pages: 89
Samsung SyncMaster S22A650D Manual Del Usuario preview
SyncMaster S22A650D
Brand: Samsung Pages: 94
Samsung SyncMaster S22A650S Manual Del Usuario preview
SyncMaster S22A650S
Brand: Samsung Pages: 95

Brands by name

Popular brands

Load more brands