manualshive.com logo in svg

Suzuki SMD12, Operator'S Manual

The Suzuki SMD12 Operator's Manual is the essential companion for any Suzuki SMD12 owner. With easy-to-follow instructions and detailed diagrams, this manual guides users through every aspect of operating and maintaining their SMD12. Download it for free from our website now and unlock the full potential of your Suzuki SMD12.

Share
Download
background image

13.  AIS, DSC MESSAGE

13-6

13.10 AIS List

The AIS list provides information about the AIS targets you are receiving navigation 
data from.

How to open the AIS list

Open the home screen, then tap [Lists] and [AIS]. 

The vertical bar at the right side of the list is colored according to that vessel’s AIS tran-
sponder type or vessel’s status.

Blue

: Class A AIS transponder

Green

: Class B AIS transponder

Red

: Dangerous AIS target

You can sort the list with the buttons on the title bar of the window.

[Name]

: AIS targets sorted in alphanumeric order.

[Range]

: AIS targets sorted by range in ascending order.

[CPA]

: AIS targets sorted by CPA in ascending order.

[Refresh]

 updates the list.

Note: 

AIS SART target appears at the top of the list.

List sort buttons

Summary of Contents for SMD12



















































































































































































































































































































































Reviews:

No comments

Related manuals for SMD12

NEC MultiSync XG-1352 Operation Manual preview
MultiSync XG-1352
Brand: NEC Pages: 38
Valcom VL550 Quick Start Manual preview
VL550
Brand: Valcom Pages: 3
Barco NX--4 Product Specifications preview
NX--4
Brand: Barco Pages: 2
Barco NX--4 Brochure & Specs preview
NX--4
Brand: Barco Pages: 4
Leyard Planar LookThru LO55 Fabricator’S Manual preview
Planar LookThru LO55
Brand: Leyard Pages: 23
Planar Dome EX User Manual preview
Dome EX
Brand: Planar Pages: 62
WAGO JUMPFLEX 2857 Series Operating And Assembly Instructions preview
JUMPFLEX 2857 Series
Brand: WAGO Pages: 2
ViewSonic VX2267-mhd User Manual preview
VX2267-mhd
Brand: ViewSonic Pages: 47
Samsung SyncMaster 650FP Quick Start Manual preview
SyncMaster 650FP
Brand: Samsung Pages: 25
Samsung S19E450BR User Manual preview
S19E450BR
Brand: Samsung Pages: 146
Key-Disp KD831 User Manual preview
KD831
Brand: Key-Disp Pages: 12
Slingbox SBPB1 Quick Setup Manual preview
SBPB1
Brand: Slingbox Pages: 12
LARTET DN-107P Operation Manual preview
DN-107P
Brand: LARTET Pages: 33
Acnodes RMW8215 User Manual preview
RMW8215
Brand: Acnodes Pages: 18
Spacetronik SPD-M432T User Manual preview
SPD-M432T
Brand: Spacetronik Pages: 8
Sharp PN-V601A Setup Manual preview
PN-V601A
Brand: Sharp Pages: 40
Philips 107B50/74 Service Manual preview
107B50/74
Brand: Philips Pages: 75
Dell E153FPTc Service Manual preview
E153FPTc
Brand: Dell Pages: 69

Brands by name

Popular brands

Load more brands