manualshive.com logo in svg

Suzuki SMD12, Operator'S Manual

The Suzuki SMD12 Operator's Manual is the essential companion for any Suzuki SMD12 owner. With easy-to-follow instructions and detailed diagrams, this manual guides users through every aspect of operating and maintaining their SMD12. Download it for free from our website now and unlock the full potential of your Suzuki SMD12.

Share
Download
background image

8.  FISH FINDER (SOUNDER)

8-5

8.3.5

Bottom discrimination display

The bottom discrimination display, which requires a bottom discrimination capable 
transducer or Bottom Discrimination Sounder FURUNO BBDS1 or Network Fish Find-
er FURUNO DFF1-UHD, identifies probable bottom composition. The display is avail-
able in all screen divisions, single or dual frequency mode, and occupies the bottom 
1/6 of the screen in the full screen display. 

Use this feature with ship speed 10 knots or less and depths between 5 and 100 m.

Note 1: 

Composition estimate accuracy may be affected when the transducer is not 

parallel with the seabed.

Note 2: 

When the bottom discrimination feature is active, picture advance speed may 

be affected.

How to activate or deactivate the bottom discrimination display

1. Open the home screen, then tap [Settings] - [Sounder].
2. Tap [Fish Finder Source].
3. Tap [SMD12], [SMD16], [BBDS1] or [DFF1-UHD] as applicable.
4. Tap the close button to finish.
5. To activate or deactivate the bottom discrimination display, turn [Bottom] on or off 

from the pop-up menu.

Bottom

discrimination 

display 

Rock

Gravel

Sand

Mud

Sand and rock are the most likely bottom type in this example.

ft

HF/LF

576

(S)

Summary of Contents for SMD12



















































































































































































































































































































































Reviews:

No comments

Related manuals for SMD12

Bacharach HGM-SZ Supplementary Manual preview
HGM-SZ
Brand: Bacharach Pages: 5
FDI ELI Series User Manual preview
ELI Series
Brand: FDI Pages: 16
Samsung Samsung 900S Manual Del Usuario preview
Samsung 900S
Brand: Samsung Pages: 60
Samsung 400DXn - SyncMaster - 40" LCD Flat Panel... Quick Start Manual preview
400DXn - SyncMaster - 40" LCD Flat Panel...
Brand: Samsung Pages: 24
Samsung SyncMaster 2032BW Service Manual preview
SyncMaster 2032BW
Brand: Samsung Pages: 61
Samsung SyncMaster MD230X3 User Manual preview
SyncMaster MD230X3
Brand: Samsung Pages: 42
Samsung 400UXn-M - 40" LCD Public Info Display Manual Del Usuario preview
400UXn-M - 40" LCD Public Info Display
Brand: Samsung Pages: 50
NEC AS241W-BK User Manual preview
AS241W-BK
Brand: NEC Pages: 18
Samsung SyncMaster 400CX-2 Quick Start Manual preview
SyncMaster 400CX-2
Brand: Samsung Pages: 36
Samsung 400MX - SyncMaster - 40" LCD Flat Panel... User Manual preview
400MX - SyncMaster - 40" LCD Flat Panel...
Brand: Samsung Pages: 205
Samsung SyncMaster 173P Manual Del Usuario preview
SyncMaster 173P
Brand: Samsung Pages: 54
Acer KG252Q User Manual preview
KG252Q
Brand: Acer Pages: 15
Summer IN VIEW 2.0 PLUS Quick Start Manual preview
IN VIEW 2.0 PLUS
Brand: Summer Pages: 2
DALIAN GOODDISPLAY CO. 07502-2 Manual preview
07502-2
Brand: DALIAN GOODDISPLAY CO. Pages: 38
Buffalo FTD-G731AS Service Manual preview
FTD-G731AS
Brand: Buffalo Pages: 57
ElectrIQ eiQ-43CVSUWD120FSH User Manual preview
eiQ-43CVSUWD120FSH
Brand: ElectrIQ Pages: 21
Compaq Q2009 - Compaq - Widescreen LCD Monitor Setup Poster preview
Q2009 - Compaq - Widescreen LCD Monitor
Brand: Compaq Pages: 1
Sanitas SBM 50 Instructions For Use Manual preview
SBM 50
Brand: Sanitas Pages: 80

Brands by name

Popular brands

Load more brands