Suzuki LT-A400 Service Manual Download

Page: 435 / 502

Manual Transmission: 5B-12

• Apply a small quantity of thread lock to the gearshift

shaft stopper (2) and tighten it to the specified torque.

: Thread lock cement 99000–32030

(THREAD LOCK CEMENT SUPER 1303 or
equivalent)

Tightening torque
Gearshift shaft stopper (b): 19 N·m (1.9 kgf-m,
13.5 lb-ft)

• Check the gearshift cam stopper moves smoothly.
• Make sure that the gearshift cam is in the neutral

position.

• Install the gearshift cam stopper plate (3).

NOTE
Align the gearshift cam pin “A” with the
gearshift cam stopper plate hole “B”.

• Install the spring to the gearshift cam shaft properly.

• Install the gearshift shaft assembly while aligning the

spring ends with the gearshift shaft stopper.

• Install the clutch cover. Refer to “Clutch Removal and

Installation (LT-F400/F) in Section 5C (Page 5C-3)”.

Gearshift Linkage Inspection (LT-F400/F)

B827H15206021

Refer to “Gearshift Shaft / Gearshift Cam Plate Removal
and Installation (LT-F400/F) (Page 5B-11)”.

Gearshift Shaft

Check the gearshift for bend or wear.
Check the return spring for damage or fatigue.
If any defects are found, replace the defective part(-s).

Gearshift Shaft Oil Seal

Inspect the gearshift shaft oil seal lip for damage or
wear. If any defect are found, replace the oil seal with a
new one.

(b)

I827H1520028-01

“A”

“B”

I827H1520038-01

I827H1520029-01

I827H1520030-01

I827H1520039-01

I827H1520040-01

Summary of Contents for LT-A400























































































































































































































































































































































































































































































































Search results

Summary of Contents for LT-A400

Reviews:

Related manuals for LT-A400

Brands by name

Popular brands

Suzuki LT-A400, Service Manual

Search results

Summary of Contents for LT-A400

Reviews:

Related manuals for LT-A400

Brands by name

Popular brands