background image

Hayabusa-Zone.com

Bikeland.org

 - 11/12-

CUSTOMER NOTIFICATION LETTER - Page One of Two

June 10, 2008

SAFETY RECALL CAMPAIGN #2A05

CERTAIN 2008 GSX1300RK8 (HAYABUSA) MOTORCYCLES

IGNITION SWITCH INSPECTION/REPLACEMENT

Dear Suzuki Owner:

This notice is sent to you in accordance with the requirements of the National Traffic and Motor

Vehicle Safety Act.

What is the reason for this notice?

Suzuki Motor Corporation has decided that a defect which relates to motor vehicle safety exists

in certain 2008 model year GSX1300RK8 motorcycles. Suzuki Motor Corporation is conducting

a voluntary Safety Recall Campaign. According to our records, you are the owner of one of these

motorcycles.

What is the problem?

Suzuki Motor Corporation has determined that certain GSX1300RK8 motorcycles may have the

ignition switch lead wire improperly routed. Handlebar movement can result in abnormal flexing

and damage to the ignition switch lead wire. Damage to the ignition switch lead wire can result

in intermittent or complete loss of electrical power, which can result in loss of lighting and/or

stalling of the engine. This could result in a crash.

What is Suzuki doing to solve the problem?

The repair consists of thoroughly inspecting the ignition switch lead wire routing. If the ignition

switch lead wire is not routed or clamped properly, Suzuki will replace the ignition switch/lead

wire assembly. Your original lock set will be installed onto the new ignition switch/lead wire

assembly so that your original key will operate the ignition switch. Repair time is approximately

1.3 hours and will be performed at no cost to you for parts or labor.

How do I receive the fastest possible service?

Suzuki understands that your riding time is precious. Our suggestion is to work closely with your

authorized dealer to get the recall service scheduled and performed on your motorcycle as quickly

as possible. Schedule an appointment for the recall service to be performed. Parts are currently

available. It will be necessary for your dealer to order the parts. It may be necessary to leave your

motorcycle with the dealer overnight, so check with your dealer.

To minimize the risk of injury or death, we recommend that you do not ride, or allow anyone

else to ride, your 2008 model year GSX1300RK8 (Hayabusa) until your motorcycle has been

repaired by your Suzuki dealer.

Suzuki strongly recommends that you do not ride your affected 2008 GSX1300RK8 (Hayabusa)

motorcycle until the ignition switch inspection/replacement has been completed

Summary of Contents for k8 gsx1300r













Reviews: