Suzuki GSX1300BKA Supplementary Service Manual Download Page 22

Page: 22 / 108

2D-3 Wheels and Tires:

Front Wheel Assembly Removal and Installation
(GSX1300BKAK8)

B823H32406017

Removal

1) Remove the front wheel speed sensor (1).

2) Remove the front wheel assembly (2). Refer to

“Front Wheel Assembly Removal and Installation in
related manual”.

Installation

1) Install the front wheel assembly. Refer to “Front

Wheel Assembly Removal and Installation in related
manual”.

2) Check the clearance between the front wheel speed

sensor and sensor rotor using the thickness gauge.

Special tool

(A): 09900–20803 (Thickness gauge)
(B): 09900–20806 (Thickness gauge)

Wheel speed sensor – Sensor rotor clearance
0.3 – 1.5 mm (0.012 – 0.059 in)

I823H3240001-01

I823H3240002-01

(A),(B)

I823H3240003-01

Summary of Contents for GSX1300BKA













































































































Search results

Summary of Contents for GSX1300BKA

Reviews:

Related manuals for GSX1300BKA

Brands by name

Popular brands

Suzuki GSX1300BKA, Supplementary Service Manual

Search results

Summary of Contents for GSX1300BKA

Reviews:

Related manuals for GSX1300BKA

Brands by name

Popular brands