manualshive.com logo in svg

Superrollo GW180, Operating And Assembly Manual

Share
Download
Superrollo GW180 Operating And Assembly Manual Download Page 11

11

EN

5.1  Description of the safety functions

Obstacle detection

The movement of the belt is monitored. If the roller 

shutters hit an obstacle in the DOWN ( 

t 

) direction, the 

belt will stop moving and the superrollo GW180 / GW185 

is switched off.

i

  Once the system has switched off, it is not 

possible to directly operate the drive in the 

same direction.

 

◆

First, run the belt winder back in the  

opposite direction and remove any  

possible obstacle. 

 

◆

Then it is possible to operate the drive  

in the original direction again.

Overload cut-off
The superrollo GW180 / GW185 is equipped with  

an overload cut-off system.

If the drive jams in the UP ( 

▲ 

) direction (for example, 

due to ice), the superrollo GW180 / GW185 is switched off. 

 

◆

First, remove the cause of the overload.

 

◆

Then the superrollo GW180 / GW185 is fully  

operational again in both directions.

i

There is a risk of injury if the obstacle detection is 

not working.

 

◆

The belt must be wound on as evenly as possible to 

ensure safe and correct functioning of the obstacle 

detection function.

 

◆

Please ensure that the belt winds as straight and 

evenly as possible into the device during its subse-

quent cycle after the obstacle detection system has 

triggered.

Summary of Contents for GW180













































Reviews:

No comments

Brands by name

Popular brands

Load more brands