Supermicro SuperStorageSystem SSG-2028R-DN2R48L, User Manual

Page: 7 / 85

Chapter 1: Introduction SUPERSTORAGESYSTEM SSG-2028R-DN2R48L User's Manual
1-2 1-3
Note: For your system to work properly, please follow the links below to download
all necessary drivers/utilities and the user’s manual for your server.
•
Supermicro product manuals: http://www.supermicro.com/support/manuals/
•
Product drivers and utilities: ftp://ftp.supermicro.com
•
Product safety info: http://www.supermicro.com/about/policies/safety_
information.cfm
•
If you have any questions, please contact our support team at:
Support@supermicro.com
1-2 Motherboard Features
At the heart of the SuperStorageSystem SSG-2028R-DN2R48L is the X10DSN-TS,
a dual processor motherboard based on the C612 chipset. Below are the main
features of the system (See Figure 1-1 for a block diagram of the motherboard).
Processors
The motherboard supports dual E5-2600 v3/v4 series processors in two Socket
R3-LGA 2011 sockets. Please refer to the motherboard description pages on
the Supermicro web site for a complete listing of supported processors (
www.
supermicro.com ).
Memory
The motherboard has sixteen (16) DIMM slots that can support up to 1 TB RDIMM
or 2 TB 3DS LRDIMM of DDR4 (288-pin) ECC 2400/2133/1866/1600 MHz speed
memory at 1.2v voltage. Modules of the same size and speed are recommended. DIMM
sizes of 4 GB, 8 GB, 16 GB, 32 GB, 64 GB, 128 GB (3DS LRDIMM only) size
are supported See Chapter 5 for details.
Serial ATA
Two (2) SATA 3.0 connectors that support Super DOMs (with power pins built-in)
(S-SATA 0/1). The system supports RAID 0, 1, 5 and 10.
Note: The operating
system you use must have RAID support to enable the hot-swap capability and
RAID function.
PCI Expansion Slots
The motherboard has the following PCI-E slots available on the serverboard:
•
One (1) PCI-Express 3.0 x16 low-profile slots
•
One (1) PCI-Express 3.0 x8 low-profile slots
•
One (1) SIOM slot
I/O Ports
The rear I/O LAN ports include: one Intel X540 10-Gigabit Ethernet Dual-Channel
Controller for 10G-LAN (TLAN) 1/10G-LAN (TLAN) and one IPMI-dedicated LAN
supported by the ASpeed AST2400 BMC
Two (2) USB 3.0 ports on the rear I/O panel (USB 0/1) and one (1) Type A USB 3.0
connector for front access (USB 2) are provided. Additionally, one (1) VGA connector
and one (1) serial header on the serverboard are available.
Graphics Controller
The X10DSN-TS features an integrated ASpeed 2400 BMC Video Controller.
Notes:
Note 1: The CPU maximum thermal design power (TDP) is subject to chassis
and heatsink cooling restrictions. For proper thermal management, please check
the chassis and heatsink specifications for proper CPU TDP sizing.
Note 2: For IPMI configuration instructions, please refer to the Embedded IPMI
Configuration User's Guide available at http://www.supermicro.com/support/
manuals/ .
Note 3: It is strongly recommended that you change BMC log-in information upon
initial system power-on. The manufacture default username is ADMIN and the
password is ADMIN. For proper BMC configuration, please refer to
http://www.
supermicro.com/products/info/files/IPMI/Best_Practices_BMC_Security.pdf .