manualshive.com logo in svg

Supermicro SBI-7426T-SH, User Manual

The Supermicro SBI-7426T-SH is a cutting-edge server system designed for optimal performance and scalability. Unlock the full potential of this powerful device with the comprehensive User Manual, available for free download at manualshive.com. Get step-by-step instructions and valuable insights to maximize your product experience.

Share
Download
background image

5-13

Chapter 5: BIOS

Parameter 
Selector

This static display shows the parameter of your MAC Address configuration.

MAC Address

The BIOS will automatically enter the MAC address of your system; however it 
may be over-ridden. MAC addresses are 6 two-digit hexadecimal numbers (base 
16, 0~9, A, B, C, D, E and F) separated by dots (such as 00.30.48.D0.D4.60). 

Current MAC 
Address in 
BMC

This static display shows the current MAC address used for your IPMI 
connection.

Subnet Mask

Subnet masks tell the network which subnet this system belongs. The value of 
each three-digit number separated by dots should not exceed 255.

Parameter 
Selector

This static display shows the parameter of your Subnet Masks configuration.

Subnet Mask

This static display shows the current Subnet Mask setting for your IPMI 
connection.

Current Subnet 
Mask in BMC

This static display shows the current Subnet Mask used for your IPMI 
connection.

Gateway 

Address

Enter the Gateway address for your system using this sub-menu. This should be 
in decimal and dotted quad form (such as 192.168.10.253). The value of each 
three-digit number separated by dots should not exceed 255.

Parameter 
Selector

This static display shows the parameter of your Gateway Address configuration.

Gateway 
Address

The BIOS will automatically enter the Gateway address of your system; however 
it may be over-ridden. MAC addresses are 6 two-digit hexadecimal numbers 
(base 16, 0~9, A, B, C, D, E and F) separated by dots (such as 
00.30.48.D0.D4.60). 

Current IP 
Address in 
BMC

This static display shows the current Gateway address used for your IPMI 
connection.

Table 5-12. Remote Access Configuration Sub-menu 

Menu Option

Description

Remote Access

This option allows you to select your remote access type. Options include COM1 
and 

COM2

.

Serial Port Number

This option allows you to select a serial port for console redirection if the 
selected port is enabled. Options include COM1 and 

COM2

. 

The Base Address IRQ is displayed statically under this option for your 
reference.

Serial Port Mode

Use this option to select the serial port mode setting. Options include 

115200 

8,n,1

 / 57600 8,n,1 / 38400 8,n,1 / 19200 8,n,1 / 09600 8,n,1

Flow Control

This option allows you to select Flow Control for redirection. Options include 

None

, H

ARDWARE

 or S

OFTWARE

.

Table 5-11. IPMI Configuration Sub-menu  (Continued)

Menu Option

Description

Summary of Contents for SBI-7426T-SH







































































Reviews:

No comments

Related manuals for SBI-7426T-SH

Brands by name

Popular brands

Load more brands