Supermicro A+ Server 2123BT-HNC0R User Manual Download Page 35

Page: 35 / 118

Chapter 3: Maintenance and Component Installation

Memory Installation

Memory Support

The H11DST-B supports Up to 2 TB of ECC DDR4 2666 MHz speed, RDIMM/LRDIMM/3DS/
NVDIMM memory in sixteen slots. Refer to the table below for additional memory information.
Check the Supermicro website for possible updates to memory support.

Processors and their Corresponding

Memory Modules

CPU#

Channel Channel Channel

Channel

4 DIMMS

CPU1

8 DIMMS

CPU1

8 DIMMS

CPU1

CPU2

16 DIMMS

CPU1

CPU2

Populating RDIMM/RDIMM 3DS/LRDIMM/LRDIMM 3DS DDR4

Memory Modules

Type

DIMM

Population

Maximum DIMM

Capacity (GB)

Maximum Frequency

(MHz)

1 Channel 8 Channel

RDIMM

16GB

128GB

2666

32GB

256GB

2666

LRDIMM

64GB

512GB

2666

128GB

1TB

2666

LRDIMM 3DS

2R2H

64GB

512GB

2666

2R4H

128GB

1TB

2666

Summary of Contents for A+ Server 2123BT-HNC0R























































































































Search results

Summary of Contents for A+ Server 2123BT-HNC0R

Reviews:

Related manuals for A+ Server 2123BT-HNC0R

Brands by name

Popular brands

Supermicro A+ Server 2123BT-HNC0R, User Manual

Search results

Summary of Contents for A+ Server 2123BT-HNC0R

Reviews:

Related manuals for A+ Server 2123BT-HNC0R

Brands by name

Popular brands