background image

Installation and Operation Instructions

Superior

TM

 Direct-Vent Gas Fireplace

P/N 126721-01   Rev. A   01/2014

PFS

®

US

C

Models

DRT4036TEN

DRT4036TEP

DRT4042TEN

DRT4042TEP

P126721-01

INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.

Installateur : Laissez cette notice avec l’appareil.
Consommateur : Conservez cette notice pour consultation ultérieure.

A barrier designed to reduce the risk of burns 

from the hot viewing glass is provided with this 

appliance and shall be installed.

Une barrière conçue pour réduire le risque de brûlure 

par le hublot chaude est fournie avec l’appareil et doit 

être installé.

This appliance may be installed in an aftermarket permanently located, manufactured home (USA only) or mobile 

home, where not prohibited by local codes. This appliance is only for use with the type of gas indicated on the 

rating plate. This appliance is not convertible for use with other gases, unless a certified kit is used.

WARNING AVERTISSEMENT AVISO

HOT GLASS

 WILL 

CAUSE BURNS.

DO NOT TOUCH

 GLASS 

UNTIL COOLED.

NEVER ALLOW

 CHILDREN 

TO TOUCH GLASS.

UNE SURFACE VITRÉE CHAUDE

 PEUT 

CAUSER DES BRÛLURES.

LAISSER REFROIDIR

 LA SURFACE VITRÉE 

AVANT D’Y TOUCHER.

NE PERMETTEZ JAMAIS

 À UN ENFANT DE 

TOUCHER LA SURFACE VITRÉE.

EL VIDRIO CALIENTE 

CAUSARÁ QUEMADURAS.

USTED DEBE 

NUNCA TOCAR 

EL VIDRIO CALIENTE.

LOS NIÑOS DEBEN 

NUNCA 

TOCAR EL VIDRIO.

WARNING: If the information in these 

instructions is not followed exactly, a fire or 

explosion may result causing property damage, 

personal injury or death.

AVERTISSEMENT : Assurez-vous de bien suivre les 

instructions données dans cette notice pour réduire au 

minimum le risque d’incindie ou d’explosion ou pour éviter 

tout dommage matériel, toute blessure ou la mort.

 

 Do not store or use gasoline or other 

flammable vapors and liquids in the vicinity 

of this or any other appliance.

 

 WHAT TO DO IF YOU SMELL GAS: 

• 

 Do not try to light any appliance. 

• 

 Do not touch any electrical switch; do not 

use any phone in your building. 

• 

 Immediately call your gas supplier from 

a neighbor’s phone. Follow the gas 

supplier’s instructions. 

• 

If you cannot reach your gas supplier, call 

the fire department.

 

Installation and service must be performed 

by a qualified installer, service agency or the 

gas supplier.

 

 Ne pas entreposer ni utilizer d’essence ni d’autres 

vapeurs  ou liquides inflammables dans le voisinage 

de cet appareil ou de tout autre appareil.

 

 QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ : 

• 

 Ne pas tenter d’allumer d’appareil.

• 

Ne touchez à aucan interrupteur. Ne pas vous 

servir des téléphones se trouvant dans le bâtiment 

où vous trouvez.

• 

Appelez immédiatement votre fournisseur de 

gaz depuis un voisin. Suivez les instructions du 

fournisseur.

• 

Si vous ne pouvez rejoindre le fournisseur de gaz, 

appelez le service des incindies.

 

L’installation et l’entretien doivent être assurés par un 

installateur ou un service d’entretien qualifié ou par le 

fournisseur de gaz.

Summary of Contents for DRT4036TEN













































Reviews: