Wi-Fi Compatible RGBW Controller with
Sync-able RF Touch Color Re
mote
Instruction Sheet
Part Number:
Important: Read all instructions prior to installation.
866-590-3533
B
+
-
S
+
-
M
+
-
M
+
-
To select a static color from any mode:
Press the color wheel to select your color. Brightness is adjustable
To select the color white from any mode:(Method 1)
Press the color wheel to select a static color.
Then press “Mode + button” once. Brightness is
adjustable.
To select the color white from any mode:(Method 2)
Press and hold “Mode - button” until the controller
stops at the previous static color(Mode 1).
Then press “Mode + button” once(Mode 2).
Brightness is adjustable.
MODE +
MODE -
Parts Included
RF Remote
White Mode
Static Color Mode
LDRF-RGBW6-TC4
2.4G
wifi capable
LED controller
sold seperately
1 - 2.4GHz Wi-Fi Compatable RGB Controller
1 - 2.4GHz Sync-able RF Touch Color Remote
1 - Double-sided Tape
RF remote controller has a signal range
up to 65ft (20m) and requires 2 x AAA
batteries (not included).
Button
Functions
Turn all LEDs on and off,
retaining the last setting
COLOR WHEEL
Directly select color on wheel
from any mode or color selection
BRIG/-
Dim LEDs in any static color
mode and most dynamic modes
by pressing (-) symbol. Brighten
LEDs by pressing (+) symbol
SPEED +/-
Increase (+) and decrease (-)
speed on dynamic modes
MODE +/-
Cycle up or down through 13
different dynamic modes and
static white, static color modes.
(Color Wheel)
B
+
-
S
+
-
M
+
-
Pre-test & Configure
May be used with RGBW strips or bars.
Connect LEDs to power supply and controller (see “Method 1” or “Method 2”
diagram).
Turn on LEDs using the included remote controller to ensure proper operation
of the LEDs, power supply, controller, and remote.
Choose suitable dry location for the power supply and controller. Before
double-sided tape is used, ensure all surfaces are clean and dry.
LDRF-RGBW6-TC4 4 channel RGBW (Red, Green, Blue, and White)
LED controller with color touchwheel for directly selecting a wide range of
colors.
Controller/Remote sets come preprogrammed and ready for use.
Offers 13 dynamic modes and static white, static color modes with
adjustable brightness, speed and mode retention (controller resumes
modes with the settings previously selected).
General Description
Instructions
If additional controllers or remotes are required, follow instructions
below.
The LDRF-RGBW6-TC4 features RF remote to controller device
pairing to help eliminate interference from other nearby units. If you
wish to control several controller devices from a single RF remote,
the controllers first must be re-programmed.
The easiest way to re-program several controllers at once is to have
them share a power supply or all plug in to a single power strip.
Once programmed you can provide power as you would otherwise,
sharing is only needed for the programming phase to ease the
process -- Re-programming can be done one device at a time also.
SPEED +
SPEED -
Controller Pairing:
Pairing a remote to a controller:
1. Wire all controllers to one power supply or power strip
and turn the power off.
2. Turn on the power supply or power strip and press
the “Speed + button” once within 3 seconds.
3.
If successful the LED product will flash twice slowly.
4.
If the LED product flashes nine times quickly or not at
all, repeat steps one and two.
Unpairing a remote to a controller:
1. Wire the controller to a power supply or power
strip and turn the power off.
2. Turn on the power supply or power strip and
press and
hold the “Speed + button” once within 3 seconds.
3.
If successful the LED product will flash nine times
quickly.
4.
If the LED product flashes twice slowly or not at all,
repeat steps one and two.
Pairing Note:
1. One remote can be paired to any number of
controllers.
2. One controller can be paired to up to four remotes.
Controller Pairing
