SuperATV LK-P-RZRXP-3-5 Installation Instructions Manual Download Page 1

© 2013 SuperATV.com. All Rights Reserved. 

IN-LK-P-RZRXP-3-5 11/13/2013

Polaris RZRXP 3”-5” Lift Kit

INSTALLATION INSTRUCTIONS

740B Clifty Drive • Madison, Indiana 47250 • 812-574-7777

Liability Statement

SuperATV’s products are designed to best fit users ATV/UTV under stock conditions. 

Adding,  modifying,  or  fabricating  any  factory,  or  aftermarket,  parts  will  void  any 

warranty  provided  by  SuperATV  and  is  not  recommended.  SuperATV’s  products 

could interfere with other aftermarket accessories. If user has aftermarket products 

on machine, contact SuperATV to verify that they will work together.
Although SuperATV has thousands of satisfied customers, user should be aware 

that installing lift kits, long travel, or suspension kits, tires, etc will change the ride 

of machine and may increase maintenance and part wear. Operating any off-road 

machine  while,  or  after,  consuming  alcohol  and/or  drugs  increases  risk  of  bodily 

harm or death. No warranty or representation is made as to this product’s ability to 

protect user from severe injury or death. SuperATV urges operators and occupants 

to wear a helmet and appropriate riding gear at all times.
By purchasing and installing SuperATV products, user agrees that should damages 

occur,  SuperATV  will  not  be  held  responsible  for  loss  of  time,  use,  labor  fees, 

replacement parts, or freight charges. SuperATV, nor any 3rd party, will not be held 

responsible for any direct, indirect, incidental, special, or consequential damages 

that result from any product purchased from SuperATV. The total liability of seller to 

user for all damages, losses, and causes of action, if any, shall not exceed the total 

purchase price paid for the product that gave rise to the claim.
SuperATV will warranty only parts provided by SuperATV. Any damage or problems 

with OEM housings, bearings, seals, or other manufacturers products will not be 

covered by SuperATV. SuperATV parts and products are not warrantied if item was 

not installed properly, misused, or modified.

Read instructions and view illustrations before beginning.

Need help with your installation?

1-812-574-7777

[email protected]

www.superatv.com

8:00am - 9:00pm EST M-Th

8:00am - 7:00pm EST Friday

9:00am - 2:00pm EST Saturday

Thank You
 

For Choosing

C

A

B

(Driver Side)

(Passenger Side)

Item

Description

Qty

A

Front Bracket (Aft)

1

B

Front Bracket (Fore)

1

C

Rear Shims

2

Spacer, 35mm Lg.

T

Spacer, 30mm Lg.

U

Spacer, 25mm Lg.

V

Item

Description

Qty

T

35mm Lg. Spacer

1

U

30mm Lg. Spacers

2

V

25mm Lg. Spacers

2

W

31mm Lg. Spacers

4

(Kit contents continue on following page)

Spacer, 31mm Lg.

W

Summary of Contents for LK-P-RZRXP-3-5










Reviews: