manualshive.com logo in svg

Superabrasive LAVINA ELITE L25E, User Manual

Share
Download
Superabrasive LAVINA ELITE L25E User Manual Download Page 33

Superabrasive 

 

User Manual  

Original Language 

Lavina® 25E 

 

2/2019 

33 

 

  
 
 
 

 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
 
 
 
 
 
 
 
 
 

 
 
 

 
 
 
 
 
 
 
 

 
 

 
 

 
 
 
 
 
 
 
 

 
 
 

 

3. LAVINA® 25E  TOP COVER 1 PARTS 

No. 

Item No. 

Description 

Pcs. 

1 

M6X12DIN6921 

Bolt 

7 

2 

L25LE19.20.00-1 

Inspection Cover 

1 

3 

M6X16DIN6921 

Bolt 

4 

4 

D35X1.4 

Washer 

2 

5 

L25Е10.70.00 

Gard Assembly 

1 

6 

L25E19.00.00-1 

Top Cover Assembly 

1 

7 

TWVA06000 N7T50 

V-Ring Type A 

1 

8 

M8X20DIN6921 

Bolt 

8 

9 

L25E15.10.00 

Fork 

2 

10 

M8X40DIN6921 

Bolt 

4 

11 

L20GX-15.00.29  

Bushing 

4 

4. LAVINA®25E   GARD ASSEMBLY 

No. 

Item No. 

Description 

Pcs. 

1 

M6X16DIN6921 

Bolt 

2 

2 

L30E10.71.00 

Vacuum Port 

1 

3 

L25GЕ10.70.01 

Guard 

1 

4 

L25Е10.71.00 

Bottom  Vacuum Port 

1 

5 

FBL1350-2280 

Brush 

1 

5. LAVINA®25E   TOP COVER ASSEMBLY 

No. 

Item No. 

Description 

Pcs. 

1 

L25E19.10.00-1 

Top Cover 

1 

2 

М5X10DIN933 

Bolt 

4 

3 

М5DIN7980 

Spring  Washer 

4 

4 

7-9DIN3017 

Clamp 

1 

5 

L32E19.00.05 

Tube 

1 

Summary of Contents for LAVINA ELITE L25E










































Reviews:

No comments

Brands by name

Popular brands

Load more brands