Temperature recorder and printer
21
▲
End Of Paper
–
no thermal paper
▲
No GSM Network
–
cellular communication disconnected and delay before alarm
▲
Temp Over 65C
–
ambient temperature above 65°C
▲
USB Memory Full
–
external USB memory full
▲
SD Card Full
–
external micro-SD memory full
▲
CopyProgPrnt Ended
–
message for: end of copying, data setting, & report printing
▲
Sensor Error
–
sensor failure
▲
SMS Setting
–
setting recipients, delay and repeat of SMS text messages
▲
Buzzer Setting
–
activate buzzer in every alarm event
If for 30 seconds no key is pressed,
changes will be saved
,
Saving setting
will be
displayed,
Settings saved
will be printed, and the display will revert to the readings screen.
Setting Alarm Limits to Sensor
Channel 1,2,3,4
(
Alarm type:
) enables setting limits for every channel: temperature,
humidity, voltage, etc., upper and lower, contact position and delay duration for the alarm.
1.
Press
/
until the
Settings Submenu
is displayed.
2.
Press
to enter the settings menu,
Enter password:
will be displayed.
3.
Enter a password, (4 keys in a row). If you have not yet changed your password, use the
default password:
,
,
,
. The first of the settings submenu, will appear
on the display:
Load configuration file.
4.
Scroll with
/
. Find the
Set Alarms
menu and press
.
5.
Channel No. 1 (Alarm type:)
will be displayed. The channel number will flash. To change
the channel number (1-4)/event, press
/
and press
to confirm.
6.
The event name will be displayed, for example:
Channel Alarm 1: YES
, YES will flash
(Channel 1 alarm: yes/no). To change the selection YES/NO, scroll with
/
and
press
to confirm.
7.
If
NO
is selected, the display will revert to event selection (Section 5). If the selection is
YES
, the line
Sensor 1 threshold high value: 30.0
, for example, will appear and will
indicate the upper limit value for channel no. 1. To change the value, press
/
and
to confirm. For a switch type (contact on/off), select
OFF
to activate the alarm.
8.
If, for example,
Sensor 1 threshold high delay 0010 Min
., is shown (the value 0010
will flash), the upper limit delay time for channel No. 1 is 10 minutes. The high delay time
can be set from 0 to 9,999 minutes (0000 minutes is without high delay). To change the
high delay time press
/
, to select, and press
to confirm.
9.
If, for example,
Sensor 1 threshold low value: 2.0
is shown, the lower limit delay time
for channel No. 1 is displayed. To change the value, press
/
, select, and press
to confirm (the value must be lower than the value set for the upper limit)
10.
If
Sensor 1 threshold low delay 0010 Min
., is displayed, (0010 value will flash) the
lower limit delay time for channel No. 1 is 10 minutes. The lower delay time can be set from
0 to 9,999 minutes (0000 minutes is without low delay). To change the lower delay time
press
/
, to select, and press
to confirm.
11.
The name of an alarm event will reappear, for example:
Channel No. 1 (Alarm type:)
,
the channel number will flash. To change the channel number (1-4) or to select another
alarm event, press
/
, select, and press
to confirm.
12.
To save the changes and exit the Alarm Event Setup menu, press
3 times.
Please
wait, Saving Setting
will be displayed, and then, several seconds later, the readings
screen will revert.
Settings saved
will also be printed.
Note:
When the
cursor is flashing
, a continuous pressing of the
/
when setting the
upper limit, the lower limit and the delay time will run the digits in the display faster.