manualshive.com logo in svg

Sunwave CrossFire A2, Commissioning Manual

Share
Download
Sunwave CrossFire A2 Commissioning Manual Download Page 43

 

 

MID POWER 

4 x 37dBm Output 

5G NR Compliant 

 

©  Sunwave CG_CF_M2 v2.1.0 | 43 of 47 

Contact us today:

 

www.sunwave.com 
[email protected] 

 

Figure 51.

 

Restore Configuration 

 

Software Upgrade 

The Master A2 consolidates the management of software upgrades for the entire system and saves the last software 
package information for A2, E2-O, and M2RU. Slave devices will compare the local software with the latest information 
saved in Master A2 by checking CRC at run time. If the CRC is different, slave devices will be synchronized via the current 
software package from Master A2. Therefore, when a slave device is replaced, its software will be upgraded 
automatically without any additional operation. 

Note: 

If it is the Master A2 to be replaced in a system, check the software version of the new Master A2 before 

connecting it to the system. If the software version is not the latest, upload the latest software packages to the new 
Master A2. 

 

 

Local Upgrade 

The CrossFire system supports local sync-upgrade. There are two steps for the system software local sync-upgrade. First, 
upload the software package to the Master A2. Second, slave devices are synchronized automatically via the Master A2 
if the CRC is different. Please make sure the upgrading from the lowest level device to the highest level device (M2RU -> 
E2 -> A2). The A2 must be the last one to be upgraded.  

 

As an example, to do an M2RU or E2 local upgrade: 

1.

 

Log into the OMT on the Master A2. Click the 

Upgrade

 button on the main page to navigate to the software 

upgrade page. See Figure 52. 

Summary of Contents for CrossFire A2
















































Reviews:

No comments

Brands by name

Popular brands

Load more brands