ZigBee In Wall Smart Switch
09.ZG9100A.04736
Function introduction
Important:
Read All Instructions Prior to Installation
•
DO NOT install with power applied to device.
•
DO NOT expose the device to moisture.
Safety & Warnings
Operation
•
ZigBee in wall smart switch based on latest ZigBee 3.0 protocol
•
100-240VAC Wide Input and Output Voltage
•
Supports resistive loads, capacitive loads or inductive loads
•
1 channel output, max. load up to 4.8A
•
Input and Output with Screw Terminals, Safe and Reliable
•
Enables to control ON/OFF of connected light source
•
ZigBee end device that supports Touchlink commissioning
•
Can directly pair to a compatible ZigBee remote via Touchlink without coordinator
•
Supports self-forming zigbee network without coordinator and add other devices to the network
•
Supports find and bind mode to bind a ZigBee remote
•
Supports zigbee green power feature and can bind max. 20 zigbee green power remotes
•
Compatible with universal ZigBee gateway products
•
Mini Size, Easy to be Installed into a standard size wall box
•
Radio Frequency : 2.4GHz
•
Waterproof grade: IP20
Input Voltage
Output Voltage
Output Current
Product Data
Size(LxWxH)
100-240VAC
Resistive load: max. 4.8A
Capacitive/Inductive load: max. 1.4A
100-240VAC
45.5x45x20.3mm
1.Do wiring according to connection diagram correctly.
Input Clusters
•
0x0000: Basic
•
0x0003: Identify
•
0x0004: Groups
•
0x0005: Scenes
•
0x0006: On/off
•
0x0b04: Electrical Measurement
Output Clusters
•
0x0019: OTA
ZigBee Clusters the device supports are as follows:
2.This ZigBee device is a wireless receiver that communicates with a variety of ZigBee compatible systems. This
receiver receives and is controlled by wireless radio signals from the compatible ZigBee system.
•
0x0702: Simple Metering
•
0x0b05: Diagnostics
Main Features:
• Can operate under two-wire connection with no neutral lead or three-wire connection with neutral lead
• Soft start function,
• Works with various types of switches – momentary, toggle, three-way, etc.
• Active element: semiconductor electronic switch,
• To be installed in wall switch boxes of dimensions allowing for installation, conforming to provisions of
applicable regulations,
• The Bypass is an extension unit.
The switch operates under the following loads:
• Conventional incandescent and HV halogen light sources
• ELV halogen lamps (with electronic transformers)
• MLV halogen lamps (with ferromagnetic transformers)
• Compact fluorescent CFL tube lamps with electronic ballast
• Fluorescent tube lamps with electronic ballast
• Supported light sources (power factor > 0.5) with minimal power of 3W using the Bypass (depending on the
type of load)
“Reset” Key: factory
reset of the switch,
short press to turn
on/off load
AC power input
Load output
Switch input
(2-wire with No Neutral input)
(3-wire with Neutral input)
(2-wire with No Neutral output)
(3-wire with Neutral output)
Reset
L
L
N
N
OUT
AC 100-240V
S
1
C
O
M
In-wall Smart
Switch
Ratings:100-240V,50/60Hz,
MAX:1.4A ( )
MAX:4.8A ( )
3. Zigbee Network Pairing through Coordinator or Hub
(
Added
to
a
Zigbee
Network
)
Step 1
: Remove the device from previous zigbee network if it has already been added to
,
otherwise
pairing
will
fail
.
Please
refer
to
the
part
"
Factory
Reset Manually
".
Step 2
: From your ZigBee Controller or hub interface, choose to add lighting device and enter Pairing mode as
instructed by the controller.
Step 3
: Re-power on the device to set
it into network pairing mode
(connected light flashes twice
slowly), 15 seconds timeout, repeat
the operation.
Step 4
: Connected light will blink 5
times and then stay solid on, then the
device will appear in your controller's
menu and can be controlled through
controller or hub interface.
Live
Neutral
Bypass
Reset
L
L
N
N
OUT
AC 100-240V
S
1
C
O
M
In-wall Smart
Switch
Ratings:100-240V,50/60Hz
MAX:1.4A ( )
MAX:4.8A ( )
LED indicator, stays solid on
when power on the switch, turns
off after added to a zigbee hub,
indicates (same status as connected
load) when program the switch
(network pairing, touchlink,
factory reset)
