manualshive.com logo in svg

Sunny Health & Fitness SF-B2952, User Manual, Page: 11 / 16

Share
Download
Sunny Health & Fitness SF-B2952 User Manual Download Page 11

10 

 

ADJUSTMENTS & USAGE GUIDE 

 

 

ADJUSTING THE BALANCE 

 

In  order  to  achieve  a  smooth  and  comfortable  ride,  you  must 
ensure that the bike is stabled and secured. If you notice that the 
bike  is  unbalanced  during  use,  you  should  adjust  the 

End  Caps 

(No.  30)

  located  on  the  rear  stabilizer  until  the  bike  becomes 

levelled with the floor surface. 

 

ADJUSTING THE TENSION 

 

Adjust the tension by rotating the 

Tension Control Knob (No. 17)

 

clockwise

 to increase the level of resistance. Rotate the 

Tension 

Control Knob (No. 17)

 

counter-clockwise

 to decrease the level of 

resistance. 
 
Tension  levels  are  set  at  Level  1  being  the  lowest  and  Level  8 
being the highest. 
 

 

MOVING THE BIKE 

 

To move the bike, hold 

Handlebar (No. 8) 

and tilt the bike until the 

movable wheels on the 

Left & Right

 

End Caps (No. 12 & No. 13)

 

located  on  the  front  stabilizer  touch  the  ground.  With  the  wheels 
on the ground, you can transport the bike to the desired location 
with ease. 

 

 

ADJUSTING THE HEIGHT 

 

Loosen and pull out the 

Adjustment Knob

 

(No. 10)

 to adjust the 

height  of  the  seat.  You  may  also  slide  the  seat  forward  or 
backwards  by  loosening  the 

Adjustment  Knob

 

(No.  61) 

on  the 

Seat Slider (No. 56)

. When adjusting, you will see a limit on the 

seat post and seat slider. Do NOT lift the posts passed this mark. 
Always  check  the 

Adjustment  Knob  (No.  10) 

and 

Adjustment 

Knob

 

(No.  61)

  to  ensure  that  they  are  fully  secured  when  you 

finish making an adjustment.

 

CLEANING 

The bike can be cleaned with a soft, clean, damp cloth. Do not use abrasives or solvents on plastic 
parts.  Please  wipe  your  perspiration  off  the  bike  after  each  use.  Be  careful  not  to  get  excessive 
moisture on the computer display panel as this might cause electrical hazard or electronics to fail. 
Please keep the bike, especially the computer, out of direct sunlight to prevent screen damage. 
Please inspect all assembly bolts and pedals on the bike for proper tightness every week. 

STORAGE 

Store the bike in a clean and dry environment, away from children. 

 

56 

4 

Summary of Contents for SF-B2952

















Reviews:

No comments