background image

User Manual 

 

2 Safety Instructions 

 

  

High voltage is present inside the device! 

 

Follow all the warning signs in the device. 

 

Respect all the safety instructions in this manual and other documents. 

 

The ground cable must be grounded properly, otherwise, 

 

lethal electric shock happens to the operator or installer once a fault 
occurs. 

 

device may be damaged after lightening stroke.   

 

Incorrect cable connection may cause damages to the PV cells, combiner 
box and inverter. Respect the following instructions during cable 
connection:  

 

Connect by strictly following the circuit diagram; 

 

Measure and make sure the string open-circuit voltage meets the 
requirements of the combiner box before inserting the fuse; 

 

Identify the positive pole and negative pole before connection. 

 

 

Only qualified personnel or professional electrician can perform the 
operation and wiring described in this manual. 

 

All operations and wirings must in full accordance with the national and 
local standards and requirements. 

 

All warning marks and labels must be clear and intact. Replace them if any 
damages are found. 

 

Summary of Contents for SunBox PVS-8M















































Reviews: