background image

User Manual 

 

8 Appendix 

  

39 

8.2 

 

Cable requirements 

Types 

PVS-8M

PVS-12M/ PVS-16M

Input cable 

Type: 4 mm

2

6mm

2

 Stranded flame-retarded copper wire 

Stripped length: 10mm 
Bolt: M4 
Tightening torque: 1.5N.m 

Output cable 

Type: 
50mm

2

Stranded 

flame-retarded copper 
wire 

Type: 
70mm

2

 or 90 mm

2

 Stranded 

flame-retarded copper wire 

Stripped length: 35mm 

Stripped length: 35mm 

Bolt: M10 

Bolt: M10 

Tightening torque: 20N.m 

Tightening torque: 20N.m 

Communication 
cable 

Type: 1.5mm

2

 Four core STP with low resistance 

Stripped length: 7mm 
Bolt: M3 

Tightening torque: 0.6N.m

0.8N.m 

Grounding 
terminals 

Type: 16mm

2

 Stranded flame-retarded copper wire 

Stripped length: 15mm 
Bolt: M6 
Tightening torque: 4N.m 

8.3 

 

Quality Assurance 

Where any fault occurs during the warranty period, Sungrow will maintain or replace 
the product for free. 

Evidence 

Sungrow Power Supply Co., Ltd. needs the users to provide the receipt invoice and 
the date you purchase. Meanwhile the trademark should be clearly legible. 
Otherwise Sungrow Power Supply Co., Ltd. has the right to exclude liability claims. 

Conditions 

 

The original unqualified product should return to Sungrow. 

 

Users should permit appropriate time to maintenance the device with fault for 

Sungrow. 

Summary of Contents for SunBox PVS-8M















































Reviews: