manualshive.com logo in svg

Sunell Security SN-TPC4201VT, User Manual, Page: 12 / 59

Share
Download
Sunell Security SN-TPC4201VT User Manual Download Page 12

Product Overview 

Thermal Imaging Box Network Camera 

User Manual

 

 

4 

 

Issue V1.0 (2020-10-28

）

 

 

Table 1-1

 

Interfaces 

Char 

Physical Interface 

Connection 

Audio 

Audio input/audio 
output 

Inputs the audio signal and receives the analog 
audio signals from the sound pick-up device. 

Connects to the external alarm out device, 
such as alarm light. 

GND 

Ground of system 

Connect to system ground   

Alarm 

Alarm in/ out 

Connect to alarm out and alarm in devices. 

RS232 

RS 232 port 

Connects to RS 232 peripheral. 

RS485 

RS 485 port 

Connects to the external pan & tilt 

PWR 

Power indicator light 

When the power is normal, the red light is on. 

RESET 

Reset button (RESET) 

The configuration resumes to the factory 
settings after you press the reset button for 3s. 
The default value of IP is 192.168.0.121. 

FOCUS 

Focus port   

Connect to fucus control cable of motorized 
lens. 

VIDEO 
OUT 

Analog video interface 

Sends analog video signals. User can connect 
the camera to a TV monitor through this port 
to view analog videos. 

Summary of Contents for SN-TPC4201VT




























































Reviews:

No comments