background image

Page 40

ELITE SERIES

C. 

Additional Care and Maintenance Instructions:

1.  Debris can accumulate on the spa cover. Removal of snow or other 

debris will help to avoid breakage of the foam cores. 

2.  Be sure to lock the cover straps to secure the cover from unwanted 

or accidental entry.

3.  Do not place heavy objects on the cover.

4.  Do not walk, sit or stand on the cover.

5.  Do not drag or use the flaps/skirt or the cover lock straps to remove 

the cover.

6.  Use only recommended cover lift systems. 

7.  Use only chemicals and cleaners recommended by Sundance Spas.

8.  Remember to keep spa covered when not in use. Maintaining proper 

water levels assures efficient operation and efficient electrical usage.  

9.  Do not expose your spa to the sun for extended periods of time as 

UV rays can damage the interior surface.

10. Use caution when removing cover. Before removing cover, assure all 

locks have been released to avoid lock breakage and or cover strap 

damage.

11.6  Maintaining The Synthetic Cabinet

Your new spa’s synthetic cabinet requires little or no maintenance of 

any kind. To clean, simply wipe cabinet with a clean towel and mild soap 

solution. 

CAUTION: Never spray cabinet with a garden hose for 

any reason since this action may induce an electrical 

short in the spa’s electrical equipment.

11.7  Winterizing

Your Sundance spa is designed to automatically protect itself against 

freezing when operating properly. During periods of severe freezing 

temperatures, you should check periodically to be certain that the 

electrical supply to the spa has not been interrupted. In extreme, bitter 

cold weather less than -20°F (-29°C), choose the F3 “Standard” filtration/

heating mode to prevent freezing (page 

33). 

If you do not intend to use your spa, or if there is a prolonged power 

outage during periods of severe freezing temperatures, 

it is important 

that all water be removed from the spa and equipment to protect 

against damage from freezing.

 

Summary of Contents for CONSTANCE









































































Reviews: