Sun Microsystems StorEdge D2 Installation, Operation And Service Manual Download Page 56

Page: 56 / 118

3-6

Sun StorEdge D2 Array Installation, Operation, and Service Manual • February 2002

▼

To Troubleshoot the Array When the Subsystem
LED Is Amber

1. Check the status LEDs on the power supplies and fan canisters in the rear of the

D2 array.

Refer to

FIGURE 1-12

, “LEDs on Power Supplies and Fan Canisters” on page 1-17 for

the location of the status LEDs.

2. If there is a fault on one of the fan canisters, re-seat the canister by following the

instructions for replacing a fan canister in “To Remove and Replace a Fan
Canister” on page 4-14.

3. If there is a fault on one of the power supplies, check the following:

■

Is the power cord properly seated and is power present?

■

Is the power switch turned on?

■

Re-seat the power supply by following the instructions for replacing a power
supply. See “To Remove and Replace a Power Supply” on page 4-16.

Summary of Contents for StorEdge D2























































































































Search results

Summary of Contents for StorEdge D2

Reviews:

Related manuals for StorEdge D2

Brands by name

Popular brands

Sun Microsystems StorEdge D2, Installation, Operation And Service Manual

Search results

Summary of Contents for StorEdge D2

Reviews:

Related manuals for StorEdge D2

Brands by name

Popular brands