manualshive.com logo in svg

Sun Microsystems StorEdge 3000 Series, Best Practices Manual

Share
Download
Sun Microsystems StorEdge 3000 Series Best Practices Manual Download Page 32

16

    Sun StorEdge 3000 Family Best Practices Manual

 

• March 

2007

Note – 

Do not use both in-band and out-of-band connections at the same time to 

manage the array. Otherwise conflicts between multiple operations might occur.

Saving and Restoring Configuration 
Information

An important feature of these management tools is the ability to save and restore 
configuration information in a number of ways. Using the array’s firmware 
application, the configuration information (NVRAM) can be saved to disk. This 
provides a backup of the controller-dependent configuration information such as 
channel settings, host IDs, FC protocol, and cache configuration. It does not save 
LUN mapping information. The NVRAM configuration file can restore all 
configuration settings but does not rebuild logical drives.

Sun StorEdge Configuration Service and the Sun StorEdge CLI can be used to save 
(upload) and restore (load or download) all configuration data, including LUN 
mapping information. These applications can also be used to rebuild all logical 
drives and therefore can be used to completely duplicate an array’s configuration to 
another array.

Summary of Contents for StorEdge 3000 Series























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands