Sun Microsystems Netra CT 820 Service Manual Download Page 91

Page: 91 / 132

Chapter A

Board Connector Pinouts

A-7

A.2.3

Ethernet Ports 1A and 1B Pinouts

The Ethernet ports 1A and 1B on the rear transition module for the distributed
management card use standard RJ-45 connectors. They are both 10 Mbit/sec
Ethernet ports.

Note –

The external Ethernet interface on the distributed management card and the

external Ethernet interface on the switching fabric board must be connected to
different subnets. If they are configured on the same subnet,

arp

messages will be

displayed on the distributed management card console.

FIGURE

A-6

RJ-45 Ethernet Connector Diagram

TABLE

A-5

Ethernet Ports 1A and 1B Pinouts

Pin No.

Signal

Pin No.

Signal

TX+

Not used

TX-

RX-

RX+

Not used

1 2 3 4 5 6 7 8

Summary of Contents for Netra CT 820





































































































































Search results

Summary of Contents for Netra CT 820

Reviews:

Related manuals for Netra CT 820

Brands by name

Popular brands

Sun Microsystems Netra CT 820, Service Manual

Search results

Summary of Contents for Netra CT 820

Reviews:

Related manuals for Netra CT 820

Brands by name

Popular brands