Sun Microsystems Netra CT 820 Service Manual Download Page 116

Page: 116 / 132

A-32

Netra CT 820 Server Service Manual

• July

2004

The signal interface of the connectors are described in the following two tables.

A.6.4

Fast Ethernet Connector Pinouts

The dual-jack RJ45 (J701) AMP1116353-8 Ethernet connectors, located on the
transition card’s back panel, provide two 10/100 Mbps fast Ethernet ports.

FIGURE

A-21

Fast Ethernet Connector Pins

TABLE

A-23

Serial Port A

Pin No.

Signal

Pin No.

Signal

SER_A_DCD

SER_A_DSR

SER_A_RXD

SER_A_RTS

SER_A_TXD

SER_A_CTS

SER_A_DTR

SER_A_RI

GND_A

TABLE

A-24

Serial Port B

Pin No.

Signal

Pin No.

Signal

SER_B_DCD

SER_B_DSR

SER_B_RXD

SER_B_RTS

SER_B_TXD

SER_B_CTS

SER_B_DTR

SER_B_RI

GND_B

Summary of Contents for Netra CT 820





































































































































Search results

Summary of Contents for Netra CT 820

Reviews:

Related manuals for Netra CT 820

Brands by name

Popular brands

Sun Microsystems Netra CT 820, Service Manual

Search results

Summary of Contents for Netra CT 820

Reviews:

Related manuals for Netra CT 820

Brands by name

Popular brands