Insert locking knob and hose coupling into the connec-
tion bore. Make shure that the locking knob snaps in.
2.1.3 h
And
tool
Slide hand tool over the hose coupling. Make sure that the
locking knob snaps in. For more information please refer
to the user’s manual of the hand tool.
2.1.4 A
BrAsiVe
For detailed information please refer to the user’s
technical document for the hand tool used.
The abrasive must be fastened snug against in-
stalled tools.
Let the abrasive run briefly at idling speed without load.
In the event of strong vibrations or other deficiencies shut
down the machine immediately and rectify deficiencies or
fit a new abrasive.
2.1.5 s
Afety
guArd
If a safety guard is supplied with the hand tool, it is
imperative that the safety guard be used.
2.2 r
Ating
dAtA
2.2.1 s
pecificAtions
3-phase AC motor:
Power voltage
42V/400V, 50Hz, 460V, 60Hz
Power Input
Type 3.8: 3800W, 60Hz
Type 3.2: 3200W, 50Hz
Type 2.4: 2400W, 50Hz
Power Output
Type 3.2: 2700W, 50Hz
Type 2.4: 2100W, 50Hz
Protection class
1
Type of protection
IP44
No-load speed
50Hz: 1000/1700/2700/5100/7300/13500min
-1
60Hz: 1200/2000/3200/6100/8700/17000min
-1
Sound pressure level
50Hz: 77dB(A), K=1.5m/s
2
60Hz: 80dB(A), K=1.5m/s
2
Flexible shafts with connection thread DIN15:
DIN15, NA10, NA12, NA15
M14 see catalog
2.2.2 V
iBrAtion
mesurement
VAlues
of
hAnd
tools
FH15
Test grinding wheel ø 100x25
Measurement value <2.5m/s
2
/K=1.5m/s
2
Drive 8700min
-1
WH15
Test grinding wheel ø 100x25
Measurement value <2.5m/s
2
/K=1.5m/s
2
Drive 5100min
-1
SAM 1:1
Test grinding wheel ø 230x6
Measurement value <2.5m/s
2
/K=1.5m/s
2
Drive 6100min
-1
TAM 1:1
Test grinding wheel ø 100x25
Measurement value <2.5m/s
2
/K=1.5m/s
2
Drive 6100min
-1
According to ISO/DIS 8662.4
The specified vibration value was measured with a
standardised test method and may differ from the
actual operating value. The specified value can be
used for product comparisons or for an introductory as-
sessment of work breaks.
2.3 o
perAting
conditions
Temperature range during operation: 0 to +50°C
Relative air humidity: 90% at +30°C, 65% at +50°C
To avoid strong looping movements and beaming
of the flexible shafts, the working pressure must
be reduced.
3.
handling
/ o
Peration
3.1 m
Achine
3.1.1 s
elect
the
speed
Pull the locking pin to disengage it. Set the speed you
want by pulling or twisting the eccentric.
You may set the speed only when the tool is
switched off.
3.1.2 s
tArting
the
mAchine
Before turning on the machine, make sure to re-
move wrenches and adjusting tools.
When turning on, hold the flexible shaft extended.
During operation make sure that the flexible shafts have
25