Suez Sievers M500e Operation And Maintenance Manual Download Page 77

Page: 77 / 325

NSTALLATION

.............................

Sievers M500e TOC Analyzer

Operation and Maintenance Manual

DLM 78510-02 EN Rev. B

TEP

6: C

ONNECT

THE

AMPLE

NLET

AND

UTLET

ORTS

Online

mode, the Analyzer is designed to measure water from a continuous sample

flow. In

Grab

mode, simply insert 40-mL vials into the iOS System. No plumbing change

is required.

Configuring the Sample Inlet and Outlet Ports

Disable the flow from the water source until the sample inlet system is completely

installed and the Analyzer is ready to begin analysis.

To configure the sample inlet and outlet ports

1. Connect the 1/4" Teflon

tubing with the in-line filter to the sample inlet on the

iOS or the Sample Inlet Block, depending on the Analyzer’s configuration.

Tighten 1/4 turn past finger-tight with a 9/16" open-end wrench. Do not over-

tighten the nut.

Connect the 3/4" OD waste line tubing to the waste outlet on the sample inlet

system or the Sample Inlet Block by sliding the tubing over the barb fitting.

Place the hose clamp over the waste line and tighten, to secure the connection

to the waste outlet.

Route the waste tubing to an appropriate waste outlet. The waste is gravity-

drained, and thus the waste tubing cannot be routed above the level of the

waste from the waste line to between 50-300 mL/min. The flow rate is

controlled by a needle valve, which is adjusted by the screw on the sample

inlet system. Turn the screw clockwise to decrease flow and counter-clockwise

to increase flow.

NOTE:

Avoid setting a water flow rate that exceeds 300 mL/min,

which may result in poor system suitability verification data.

Cautions

To avoid false TOC readings and possible damage to the Analyzer, always make sure

the sample inlet is open and the DI water reservoir is filled

before

turning on the

Analyzer. Always close the door of the iOS System when not sampling from a vial.

Operation of the Analyzer without the in-line filter on the sample inlet line will damage

the Analyzer and void the warranty. To avoid damaging the Analyzer, install the filter

and replace the filter element as needed.

Summary of Contents for Sievers M500e






































































































































































































































































































































Search results

Summary of Contents for Sievers M500e

Reviews:

Brands by name

Popular brands

Suez Sievers M500e, Operation And Maintenance Manual

Search results

Summary of Contents for Sievers M500e

Reviews:

Brands by name

Popular brands