Suez Sievers M500e Operation And Maintenance Manual Download Page 175

Page: 175 / 325

ESTORING

ACKUP

.............................

Sievers M500e TOC Analyzer

Operation and Maintenance Manual

DLM 78510-02 EN Rev. B

175

Restoring a Backup

To restore a backup of the database

1. On the

Settings

reen, click the

Backup/Restore

tab.

In the

Available Backups to Restore

section, select the backup to restore.

Click

Restore Backup

. A progress bar appears, and the current database is

backed up prior to restoring the selected backup. When the process is

complete, a message appears stating that the database was successfully

restored and the Analyzer’s’ firmware must be restarted.

Click

to restart the Analyzer’s firmware. When the initialization process is

complete, the

Home

screen appears. The

Available Backups to Restore

section of the

Backup/Restore

tab on the

Settings

reen includes the new

backup file.

Summary of Contents for Sievers M500e






































































































































































































































































































































Search results

Summary of Contents for Sievers M500e

Reviews:

Brands by name

Popular brands

Suez Sievers M500e, Operation And Maintenance Manual

Search results

Summary of Contents for Sievers M500e

Reviews:

Brands by name

Popular brands