manualshive.com logo in svg

Suez Sievers M500e, Operation And Maintenance Manual

Share
Download
Suez Sievers M500e Operation And Maintenance Manual Download Page 138

C

ONFIGURING

 E

XPORT

 P

REFERENCES

.............................

Sievers M500e TOC Analyzer

Operation and Maintenance Manual

DLM 78510-02 EN Rev. B

138

SUEZ © 2022

Configuring Export Preferences

Use the 

Configuring Export Preferences

 panel to create default settings for use in 

exporting data. Also, use this panel to enable and define parameters for a daily export of 

results data from online analysis.

To configure export preferences

1. Navigate to the 

Export Preferences

 panel (

Settings

 

s

 screen > 

System Setup

 

tab).

2.

To enable a daily export of results data from online analysis:

•

Select the 

Enable Daily Export Of Online Results

 option.

•

Click inside the 

Export Time 

field and use the numeric keypad to enter a 

time (24-hour format) for the daily export.

•

Continue with the remaining steps in this procedure to create default 

settings for use in exporting data. In addition to displaying the default 

settings on the dialog boxes for exporting data, the Analyzer will use them 

for the daily export of results data.

3.

To create default settings for use in exporting data, select one of the following 

options in the 

Destination

 area:

•

USB Device

•

Network Folder

4.

For 

USB Device

:

Summary of Contents for Sievers M500e






































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands