Sub-Zero Wolf ICBDF364C Service Manual Download | Manualshive

Page: 2 / 85

background image

Page 2

1-5

#814889- Revision A- July, 2010

General Information

International Dual Fuel (ICBDF) Series

International Dual Fuel (ICBDF) Series

WARRANTY INFORMATION

This page contains a summary of the 2 & 5 Year Warranty that is supplied with every Wolf product, followed by
details and notes about the warranties.

TWO & FIVE YEAR Warranty Summary

•

Two year TOTAL PRODUCT warranty, parts and labor.

•

Limited Parts Only Warranty for the 3rd through 5th year on the following parts only:
- Electric Heating Elements
- Electronic Control Boards

Warranty Details:

The warranty applies only to products installed for normal residential use. The warranty applies only to product
installed in the United States or Canada.

Warranty Notes:

•

All warranties begin at the time of the unit’s initial installation.

•

All Warranty and Service information collected by Wolf Appliance, Inc. is arranged and stored under the unit seri-
al number and/or the customer’s name. Please note that Wolf Appliance, Inc. requests that you have the model
serial number available whenever contacting the factory or parts distributor.

(See

Figure 1-1

for Serial Tag Layout, and

Figure 1-2

for Serial Tag Location)

Wolf Appliance Company, LLC

Fitchburg, WI

Gas

INPUT RATING EACH BURNER - BTU/HR

Man. Press.

Left Rear Burner –

Other Top Burners -

Griddle –

Charbroiler –

French Top –

ELECTRICAL RATING: Volts –

Amps –

Hertz -

Model # -

Serial # -

BD

MINIMUM HORIZONTAL CLEARANCE FROM SIDES AND BACK OF APPLIANCE TO ADJACENT COMBUST-

IBLE CONSTRUCTION EXTENDING 18” ABOVE THE COOKING SURFACE 12” FROM SIDE WALLS 0” FROM

REAR WALL MINIMUM CLEARANCE BETWEEN ADJACENT COMBUSTIBLE MATERIALS BELOW THE

COOKING SURACE AND THE BACK AND SIDE OF THE APPLIANCE: 0”. MAXIMUM DEPTH FOR OVERHEAD

CABINETS IS 13” MINIMUMBERTICAL DISTANCE BETWEEN THE COOKING SURFACE AND THE BACK AND

SIDE OF THE APPLIANCE: 30”, MINIMUM VERTICAL DISTANCE BETWEEN THE TOP BROILER GRID TO

UNPROTECTED OVERHEAD COMBUSTIBLE SURFACES 36”, MINIMUM HORIZONTAL DISTANCE BETWEEN

OVERHEAD CABINETS INSTALLED TO EITHER SIDE OF THE APPLIANCE SHALL NOT BE LESS THAN THE

NOMINAL WIDTH OF APPLIANCE TO BE USED IN CONJUNCTION WITH A SUITABLE VENT HOOD ONLY.

COOKING UTENSILS SHALL NOT BE USED ON AN OPEN TOP BROILER SECTION, MINIMUM HORIZONTAL

CLEARANCE FROM ISLAND INSTALLTION COOKTOP TO COMBUSTIBLE SIDE AND BACK WALL IS 12”

“ANSI Z21.1 “HOUSEHOLD GAS COOKING APPLIANCES”

“CSA IR 58, 1995”

Figure 1-1. Typical Serial Tag Layout

Figure 1-2. Serial Tag Located Under Control Panel

Serial Tag Located

Underneath Bottom

of Control Panel

«
1
2
3
4
...
»

Summary of Contents for Wolf ICBDF364C






















































































Reviews:

No comments

Related manuals for Wolf ICBDF364C

Brand: Dacor Pages: 36

Brand: Dacor Pages: 24

Elite SE 110 Dual Fuel

Brand: Rangemaster Pages: 36

Brand: Blue Seal Pages: 33

AER5712BA Series

Brand: Maytag Pages: 9

Brand: Amana Pages: 32

Brand: Zline Pages: 40

Brand: Bertazzoni Pages: 36

Brand: Bertazzoni Pages: 46

Brand: Whirlpool Pages: 28

Brand: Whirlpool Pages: 28

Brand: Whirlpool Pages: 28

Brand: Whirlpool Pages: 32

Brand: Whirlpool Pages: 33

Brand: Whirlpool Pages: 33

Brand: Whirlpool Pages: 34

Brand: Jenn-Air Pages: 48

Brand: Jenn-Air Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands