Stryker 6086 Operation & Maintenance Manual Download Page 71

Page: 71 / 158

www.stryker.com

6086-009-001 REV B

Return To Table of Contents

OUTER, OUTER TUBE REPLACEMENT

Tools Required:

•

(2) Saw Horse

•

3/8” Combination Wrench

•

7/16” Combination Wrench

•

T25 Torx Driver

•

(2) 9/16” Combination Wrench

•

Dead Blow Hammer

•

3/16” Allen Wrench

•

1/2” Combination Wrench

•

Needle Nose Pliers

Procedure:

1. Complete steps 2-7 from “Inner, Inner Tube Replacement” on

page 69

2. Using a T25 Torx driver, remove the two button head cap screws that secure the tube bearing (see “Figure 73”

page 70

3. Remove the inner tube.
4. Remove the outer tube X-frame guard and set aside to reuse on the new outer tube (see ”Figure 72” on

page

5. Using a 3/16” Allen wrench and 1/2” combination wrench, remove the bolt that holds the timing link to the outer

tube and remove the timing link.

6. Depending on where your side release handle is located, you may need to remove the height adjustment rack

springs. Using needle nose pliers, remove the two return springs for the height adjustment rack.

7.  Using a 3/16” Allen wrench, remove the four bolts that secure the slider housing and set aside.
8.  Remove the outer tube and save the tube bushings to reuse on the new tube.
9.  Reverse the above procedures to install the new outer tube.

Note:

Make sure that the X-frame guard screw hole on the new inner tube is facing the top of the cot when

reassembling.

10. Verify proper operation of the unit before returning it to service.

Service Information

Summary of Contents for 6086































































































































































Search results

Summary of Contents for 6086

Reviews:

Brands by name

Popular brands

Stryker 6086, Operation & Maintenance Manual

Search results

Summary of Contents for 6086

Reviews:

Brands by name

Popular brands