manualshive.com logo in svg

Stryker 6086, Operation & Maintenance Manual

Share
Download
Stryker 6086 Operation & Maintenance Manual Download Page 7

www.stryker.com

6086-009-001 REV B

7

Return To Table of Contents

Symbols and Definitions

Attention, consult accompanying documents

Safe Working Load Symbol

Pinch Point

WARNING/CAUTION/NOTE DEFINITION

The words WARNING, CAUTION and NOTE carry special meanings and should be carefully reviewed.

 WARNING

Alerts the reader about a situation which, if not avoided, could result in death or serious injury. It may also describe 
potential serious adverse reactions and safety hazards.

 CAUTION

Alerts the reader of a potentially hazardous situation which, if not avoided, may result in minor or moderate injury to the 
user or patient or damage to the equipment or other property. This includes special care necessary for the safe and 
effective use of the device and the care necessary to avoid damage to a device that may occur as a result of use or 
misuse.

NOTE

Provides special information to make maintenance easier or important instructions clearer.

SYMBOLS

Summary of Contents for 6086































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands