manualshive.com logo in svg

Stryker 6086, Operation & Maintenance Manual

Share
Download
Stryker 6086 Operation & Maintenance Manual Download Page 66

66

6086-009-001 REV B

www.stryker.com

Return To Table of Contents

Figure 64:  Cot Retaining Post

C

E

B

A

D

Service Information

COT RETAINING POST ADJUSTMENT

Tools Required:

• 

3/16” Hex Wrench

 CAUTION

The cot retaining post comes preconfigured for an X-frame cot, if the fastener has been configured for an H-frame style 
cot, the cot retaining post must be adjusted to accommodate the fastener.

Procedure:

1.  Using a 3/16” hex wrench, remove the two socket head cap screws (A) that hold the pin brackets (B) to the base 

frame (C) (Figure 64).

2.  Turn the bottom pin bracket 180˚.
3.  Using a 3/16” hex wrench, reinstall the two socket head cap screws that were removed in step 1.
4.  Verify proper operation of the unit before returning it to service.

Note:  

If the arrow (D) on the bottom bracket of the retaining post (E) points toward the head end of the cot, the 

retaining post is set for an X-frame style cot. If the arrow points toward the foot end of the cot the post is set for an 
H-frame style cot (Figure 64). 

Summary of Contents for 6086































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands