manualshive.com logo in svg

Stryker 6086, Operation & Maintenance Manual

Share
Download
Stryker 6086 Operation & Maintenance Manual Download Page 56

56

6086-009-001 REV B

www.stryker.com

Return To Table of Contents

Cleaning

The  

Performance-PRO™

 XT cot is designed to be power washable.  The unit may show some signs of oxidation or 

discoloration from continuous washing, however, no degradation of the cot’s performance characteristics or functionality 
will occur due to power washing as long as the proper procedures are followed. 

Thoroughly clean the cot once a month.  Clean Velcro

®

 AFTER EACH USE. Saturate Velcro

®

 with disinfectant and allow 

disinfectant to evaporate.  Appropriate disinfectant for nylon Velcro

®

 should be determined by the service.

WASHING PROCEDURE

•  Follow the cleaning solution manufacturer’s dilution recommendations exactly.
•  The  preferred  method  Stryker  Medical  recommends  for  power  washing  the  cot  is  with  the  standard  hospital 

surgical cart washer or hand held wand unit.

WASHING LIMITATIONS

 WARNING

When cleaning, use any appropriate personal safety equipment (goggles, respirator, etc.) to avoid the risk of inhaling 
contagion.  Use of power washing equipment can aerate contamination collected during the use of the cot.

 CAUTION

• 

DO NOT STEAM CLEAN OR ULTRASONICALLY CLEAN THE UNIT.

• 

Maximum water temperature should not exceed 180°F/82°C.

• 

Maximum water pressure should not exceed 1500 psi/130.5 bar.  If a hand held wand is being used to wash the 
unit, the pressure nozzle must be kept a minimum of 24 inches (61 cm) from the unit.

• 

Allow cot to air dry.

• 

Towel dry all casters and interface points.

• 

Failure to comply with these instructions may invalidate any/all warranties.

Summary of Contents for 6086































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands