Stryker 6086 Operation & Maintenance Manual Download Page 52

Page: 52 / 158

6086-009-001 REV B

www.stryker.com

Return To Table of Contents

Optional Accessories

ATTACHING THE PEDI-MATE

INFANT RESTRAINT SYSTEM

See the Pedi-Mate

users manual for the manufacturer’s recommendations for the use, operation and care of the

Pedi-Mate

Infant Restraint System.

To secure the Pedi-Mate

to the cot:

1.  Remove any restraints that are already attached to the cot.
2.  Raise the cot backrest to the full upright position.
3.  Position the Pedi-Mate

pad flat on the backrest with the black backrest straps out (see Figure 55).

4. Wrap the straps around the backrest and insert the ends of the straps through the brackets. Securely fasten the

buckle (see Figure 56).

WARNING

To avoid accidental release of the Pedi-Mate

, and possible injury to the infant, ensure that the buckle is located away

from obstructions on the cot or accessories.

Figure 56: Fastening the Pedi-Mate

Buckle

Figure 55: Positioning the Pedi-Mate

Summary of Contents for 6086































































































































































Search results

Summary of Contents for 6086

Reviews:

Brands by name

Popular brands

Stryker 6086, Operation & Maintenance Manual

Search results

Summary of Contents for 6086

Reviews:

Brands by name

Popular brands