Stryker 6086 Operation & Maintenance Manual Download Page 49 | Manualshive

Page: 49 / 158

Stryker 6086 Operation & Maintenance Manual Download Page 49

www.stryker.com

6086-009-001 REV B

49

Return To Table of Contents

Optional Accessories

USING THE KICKSTAND FOR DIALYSIS SCALE

The kickstand is intended for weighing patients on a scale.

Note:

•

The kickstand assembly is configured for an X-frame cot retention system only.

•

The kickstand (p/n 6085-002-000) is not compatible with the optional base storage net (p/n 6500-160-000).

WARNING

•

Stryker recommends a two person operation when using the kickstand.

•

Make sure that the patient weight is centered on the cot before using the kickstand.

•

Engage the kickstand with your foot only.

•

Lower cot height prior to engaging kickstand for increased stability.

•

Make sure that the kickstand remains in the retracted position and does not engage during transport.

•

Do not use the kickstand as a brake.

•

Do not engage kickstand on a sloped surface.

To use the kickstand:

1.  Operator 1 engages the kickstand with their foot as shown in Figure 51.
2.  Operator 2 lifts the foot end of the cot at a height sufficient to actuate the kickstand.
3.  Both operators must make sure that the kickstand is in the forward locked position as shown in Figure 52.

To release the kickstand:

1. Operator 1 lifts the foot end of the cot until both wheels

are off of the floor.

2. Operator 2 rolls the cot slightly forward to make sure

that the kickstand retracts on its own as shown in
Figure 53.

Figure 51

Figure 52

Figure 53

«
...
47
48
49
50
51
...
»

Summary of Contents for 6086































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands