manualshive.com logo in svg

Stryker 6086, Operation & Maintenance Manual

Share
Download
Stryker 6086 Operation & Maintenance Manual Download Page 31

www.stryker.com

6086-009-001 REV B

31

Return To Table of Contents

LOADING AN EMPTY COT INTO A VEHICLE WITH ONE OPERATOR

 WARNING

• 

The one person loading and unloading procedures 
are for use only with an empty cot. Do not use the 
procedures when loading or unloading a patient. Injury 
to the patient or operator could result. 

• 

Ensure proper hand placement on hand grips. Hands 
should be clear of red safety bar pivots while loading 
and unloading the cot or whenever changing height 
position of the cot with two or more operators.

To load an empty cot into a vehicle with one operator:

1.  Place the cot in a loading position (any position in 

which the load wheels meet the vehicle floor height). 

2.  Lift the vehicle bumper to the raised position (if 

equipped). 

3.  Roll the cot to the open door of the patient 

 

compartment. 

4.  Push the cot forward until the loading wheels are on 

the compartment floor and the safety bar passes the 
safety hook. 

5.  Pull the cot back until the safety bar engages the 

safety hook. 

6.  Grasp the cot frame at the foot end and squeeze and 

hold the release handle (see Figure 21). 

7.  Lower the foot end of the cot to the ground, making 

sure  that the cot locks in position 1 (see Figure 22). 

8.  Lift the foot end of the cot until it is level with the 

compartment floor (see Figure 23).

9.  Grasp the base of the cot with one hand and pull up 

the base of the cot towards the litter, reducing the 
space between the base and the litter. 

10.  Push the cot into the patient compartment by guiding it 

into the cot fastener. 

 WARNING

Do not pull or lift on the safety bar when unloading the 
cot.  Damage to the safety bar could result and injury to the 
patient or operator could occur.

Figure 21:  Squeeze the Release Handle

Figure 23:  Pull Up the Base of the Cot

Figure 22:  Lower the Foot End of the Cot

Operation Guide

Summary of Contents for 6086































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands