Struck Magnatrac RS1000 Page 107 Attachment Assembly Instructions Download

Page: 107 / 117

BM107

B616

Bucket Kit

B612

Bucket Kit

B612

Bucket Kit

[001536]

[001278]

STEP 1.

Drive out

the #244 Press Pins securing one end of each of

the two (2) #1291 Pivot Pins... see Photo above.

STEP 2.

Drive out the two (2) #1291 Pivot Pins and release the

Bucket... see Photo above.

STEP 3.

Install “new” Bucket and secure in same way as previous

Bucket with #1291 Pivot Pins and #244 Press Pins... see Photo above.

NOTE:

Both #244 Pins [on one side] are trapped by Anti-Rotational 1/2”

Washers so that #244 Pins can’t rotate.

Bucket Kits

B612 / B616

Backhoe Bucket

Removal & Replacement

1291

244

Anti-Rotational

1/2” Washers

1291

244

Summary of Contents for Magnatrac RS1000






















































































































Search results

Summary of Contents for Magnatrac RS1000

Reviews:

Related manuals for Magnatrac RS1000

Brands by name

Popular brands

Struck Magnatrac RS1000, Attachment Assembly Instructions

Search results

Summary of Contents for Magnatrac RS1000

Reviews:

Related manuals for Magnatrac RS1000

Brands by name

Popular brands