Installation Guide
Strobes N’ More Triple Threat Dual Dash Light
Safety First!
Before beginning the installation and/or operation of your LEDs, the installation technician and operator must
read this manual in full,
before
installation. This document provides all the necessary information to allow your light to be
properly and safely installed to prevent severe injury or damage.
Proper installation of this product requires the installer to have
a good understanding of automotive electronics, systems and
procedures. Do not stare directly into these lights. Momentary
blindness and/or eye damage could result. Do not install this
product or route any wires in the deployment area of your air
bag. Equipment mounted or located in the air bag deployment
area will damage or reduce the effectiveness of the air bag or
become a projectile that could cause serious personal injury or
death. Refer to your vehicle owner manual for the air bag
deployment area. The User/Installer assumes full responsibility
to determine proper mounting location, based on providing
ultimate safety to all passengers inside the vehicle. If this
product uses a remote device to activate or control this
product, make sure that this control is in an area that allows
both the vehicle and the control to be operated safely in any
driving condition. Do not attempt to activate or control this
device in a hazardous driving situation.
If mounting this product requires drilling holes, the installer
must be sure that no vehicle components or other vital parts
could be damaged by the drilling process. Check both sides of
the mounting surface before drilling begins. Also, de-burr any
holes and remove any metal shards or remnants. Install
grommets into all wire passage holes. For this product to
operate at optimum efficiency, a good electrical connection
to chassis ground must be made. The recommended
procedure requires the product ground wire to be connected
directly to the NEGATIVE (-) battery post or vehicle chassis.
Do not attach the NEGATIVE (-) wire to any other existing
ground wire. It is recommended that these instructions be
stored in a safe place and referred to when performing
Maintenance and/or reinstallation of this product. FAILURE
TO FOLLOW THESE SAFETY PRECAUTIONS AND INSTRUCTIONS
COULD RESULT IN DAMAGE TO THE PRODUCT OR VEHICLE
AND/OR SEVERE INJURY TO YOU AND YOUR PASSENGERS!
TO NOTE: A 5amp fuse should be wired inline on the 12v+ (red) wire
close to the power source.
INSTALLATION
Attach suction cup mount to the exiting screws on the
ends of the light being careful not to overtighten them.
Push base of suction cup into the opening on a right and
left bracket and secure in place. Leave the screws on the
mounts loose till proper adjustment of the light against
the window is completed, then tighten the light in place.
Switch includes a flash/momentary button and a three
way ON (one color)/OFF/ON (dual color) function.
TROUBLESHOOTING
Be sure a minimum of +12 Volts is applied to red wire and
the Black wire is properly grounded
WIRING
Red
+12 Volts – Constant
Black
- 12 Volts – Ground
Blue
+12 Volts – Flash Pattern Selection
Yellow
Synchronization Wire
Violet
+12 Volts – 1
st
Color Activation
White
+12 Volts – 2
nd
Color Activation
WARRANTY
Provided this product is installed and operated in a manner consistent with its use, Strobes N’ More guarantees its dash lights for a
period of 2 years from the day of purchase. Units demonstrated to be defective within the warranty period will be repaired or replaced at the
seller’s discretion. The end user is responsible for shipping/returning the item to Strobes N’ More and we will cover the cost of return shipping.
International customers are responsible for all shipping charges. Improper installation or use of inappropriate or inadequate wiring or circuit
protection causes the warranty to be void. Applying voltage directly to the LEDs will cause immediate failure and void the warranty. Damages
resulting from improper use and/or accidents are not covered by this warranty. Aluminum will corrode if left in the elements or area of high road
salt use. Proper cleaning of the light is essential to keeping the unit in like new condition. Use of non-compatible components and assemblies
may cause damage to the system and/or personal injury and voids all warranties. Strobes N’ More LLC shall in no way be liable for other damages
including consequential, indirect or special damages whether loss is due to negligence or breach of warranty. Visit
www.StrobesNMore.com/warranty
for more information.
