Strictly Beds & Bunks Aspen Bunk Bed Assembly Instructions Manual Download Page 1

Cypress & Aspen 

Bunk Bed (All Sizes)

Assembly Instructions

IMPORTANT: 

 of 

the packaging until you are satisfied 

with your purchase.. Please keep all 

cardboard until fully satisfied.

DO NOT DISPOSE

Assembly Instructions

IMPORTANT – READ CAREFULLY – 

RETAIN FOR FUTURE REFERENCE

Single Size  Kit  C 

Double Size  Kit  G

Instructions: Cypress/Aspen

(Version April 2021)

Safety First !

(Maximum height: 20cm).

The top surface of the mattress must not be above the line ,marked on the frame 

 The size of the mattress required is detailed below:

Standard 3ft Single, Standard Length - Mattress size 90cm by 190cm
Small 3ft Single, Standard Length - Mattress size 75cm by 190cm
Standard 2ft 6 Single, Short Length - Mattress size 90cm by 160cm
Small 2ft 6 Single, Short Length - Mattress size 75cm by 160cm
Small 4ft Double, Standard length - Mattress size 120cm by 190cm
Standard 4ft 6 Double, Standard Length - Mattress size 137cm by 190cm

High beds and the upper bed of a bunk bed are not suitable for children under six years due to risk of injury 
from falls.

Be aware of the danger of young children (under 6) falling from upper bunk.

Beds should not be used if any structural part is broken or missing.

Bunk beds and high beds can present a serious risk of injury from strangulation if not used correctly. Never 
attach or hang items to any part of the bunk bed that are not designed to be used with the bed, for example, 
but not limited to ropes, strings, cords, hooks, belts and bags.

Children can become trapped between the bed and the wall, a roof pitch, the ceiling, adjoining pieces of 
furniture (eg cupboards) and the like. To avoid risk of serious injury the distance between the top safety 
barrier and the adjoining structure shall not exceed 75mm or shall be more than 230mm.

Always ensure that guardrails, ladder and other components are maintained in the proper position and free 
from damage, and all the screw fixings tight.

Always use the ladder for entering and leaving the upper bunk.

Do not allow horseplay on or under the bed and prohibit jumping on the bed.

Use a nightlight as an added safety precaution for persons under the upper bunk.

Use guardrails on both sides of the upper bunk.

Every bedroom must have at least one opening window. Ventilation of the room is necessary in order to keep 
the humidity low and to prevent mould in and around the bed. 

The bed complies with BS EN 747-1: 2012+A1 :2015 safety standards

Summary of Contents for Aspen Bunk Bed













Reviews: