Theme 22 Issue 2.1 09/07/01
Page 1 of 12
Appliance data:
Type of gas
:
Natural gas (G20) Cat. I2H
Propane gas (G31) Cat. I3P
Injector size
:
7 x 0.80 (2 off)
7 x 0.62
Injector marking
:
80
62
Gross heat input (high setting)
:
10.2kW (34,800Btu/h)
10.0kW (34,200Btu/h)
Gross heat input (low setting)
:
4.4kW (15,000Btu/h)
3.5kW (12,000Btu/h)
Supply pressure
:
20mbar (8in.w.g.)
37mbar (14.8in.w.g.)
Appliance test point pressure (cold)
:
18.0mbar (± 1.0mbar)
36.0mbar
Minimum flue diameter
:
175mm (7in.)
175mm (7in.)
Minimum effective height of chimney
:
3m (10ft.)
3m (10ft.)
Ignition
:
Piezo
Piezo
Spark gap
:
3.0mm min., 4.5mm max.
3.0mm min., 4.5mm max.
Dimensions:
Width over frame excluding trims
:
624mm
Height including frame
:
585mm
(534mm Lowline Version)
Depth
:
223mm
Shipping weight
:
42kg
Country of destination
:
United Kingdom
& Irish Republic
This appliance has been assessed by a Government appointed Notified Body and shown to meet the
'Essential Requirements' of the European Gas Appliance Directive.
The Directive lays down requirements for the safety of the appliance, together with its design,
construction, and use of materials. It also requires the production process to be covered by an
approved and monitored system of quality assurance.
Mandatory requirements
Straxgas fires must be installed with due regard to the following
mandatory
regulations:
The relevant British Standard installation specifications and codes of practice, and Building Regulations
issued by the Department of the Environment, and Building Standards (Scotland) Consolidated
Regulations issued by the Scottish Development Board.
Gas Safety (Installation and Use) Regulations.
Failure to install this appliance correctly could lead to prosecution and render the guarantee
invalid.
Attention is drawn to the latest edition of the following standards:
BS1251, Specifications of open-fireplace components.
BS5440, Part 1 Specification for installation of flues.
BS5440, Part 2 Specification for installation of ventilation for gas appliances.
BS5482, Part 2 LPG, installations in permanent dwellings.
BS5871, Part 2 Installation of decorative fuel effect gas appliances.
BS6891, Specification of low pressure gas pipework
BS8303, Replacing CP403.
This Straxgas appliance is an inset live fuel effect gas fire and must only be installed by a
competent person (e.g. a C.O.R.G.I. member) in accordance with these installation instructions.
This appliance must be installed in accordance with the rules in force, and used only in a
sufficiently ventilated space. Consult these instructions before installation and use of this
appliance.
An airbrick or similar fresh air inlet must be fitted in the room in which the fire is
installed, and must have an area not less than 18 sq.cm. (2.8 sq.in.). This fresh air inlet
must not be blocked or restricted in any way.
The air vent must be either direct to outside air or to an adjacent room which itself has a vent
direct to outside air of at least the same area.
Additional purpose made air ventilation is not normally required.
Ventilation must be provided in accordance with the rules in force.
Division of Legge Fabheat Ltd.
Longfield Road, Leamington Spa, Warks. CV31 1XB
Tel. (01926) 882233 Fax. (01926) 450846 Email: [email protected]
Registered in England No 500091
INSTALLATION AND SERVICING INSTRUCTIONS FOR THE STRAXGAS
THEME 22" WITH 22" ECOTECH BURNER
(To be left with the appliance)
IE & Northern Ireland
GB
