manualshive.com logo in svg

Strautmann Super-Vitesse CFS 3101, Operating Instructions Manual, Page: 82 / 225

Share
Download
Strautmann Super-Vitesse CFS 3101 Operating Instructions Manual Download Page 82

Design and function

 

 

 

82 

Super-Vitesse CFS 3101, 3501 / Super-Vitesse CFS 3101 DO, 3501 DO   10.13 

 

  (2)  Hydraulic cylinder of braking axle 

 

 

 

Fig. 50 

 

 

 

 

 

5.15.2.1  Emergency brake valve 

 

 

WARNING 

 

Risk of infection to people due to hydraulic oil squirting out 

under high pressure and entering the body! 

Always ensure to depressurize the pressure accumulator before 

carrying out work on the hydraulic system. 
If injuries caused by hydraulic oil occur, immediately contact the 

medical services. 

 

 

 

 

The brakes must be tested before each journey to refill the pressure 

accumulator. 

 

  

If the machine is torn off, the ripcord will actuate the emergency brake valve. The hydraulic oil then 

flows from the pressure accumulator into the brake cylinders, thus initiating the braking process. 

Couple: 

  1.  Fasten the ripcord to the tractor such that in case of the machine being torn off, the ripcord is in a 

horizontal position between tractor and machine. 

Couple after emergency braking: 

  1.  Connect the brake hose to the tractor. 
  2.  Set the brake valve at the tractor such that the hydraulic oil can flow back to the tractor. 
  3.  Press the drain valve at the emergency brake valve. 

    The hydraulic oil flows back to the tractor and the pressure accumulator is depressurized. 

  4.  Insert the ripcord with the clip connector into the borehole of the operating lever. 
  5.  Set the operating lever back to its initial position. 
  6.  Actuate the brake system of the machine several times. 

    The pressure accumulator is filled and the emergency brake valve is ready for operation again. 

Uncouple: 

  1.  Make sure that the hydraulic pipe between tractor and machine has been depressurized. 
  2.  Secure tractor and machine against accidental rolling by means of the parking brake. 

 

The emergency brake valve does not replace the parking brake! 

  3.  Remove the ripcord from the tractor. 

2 

Summary of Contents for Super-Vitesse CFS 3101


































































































































































































































Reviews:

No comments