manualshive.com logo in svg

Strautmann Super-Vitesse CFS 3101, Operating Instructions Manual, Page: 47 / 225

Share
Download
Strautmann Super-Vitesse CFS 3101 Operating Instructions Manual Download Page 47

 

Loading and unloading

 

 

Super-Vitesse CFS 3101, 3501 / Super-Vitesse CFS 3101 DO, 3501 DO   10.13 

47 

 

 

 

3.7 

Risks in case of non-observance of safety instructions and warning 

signs 

  

Non-observance of the safety instructions and warning signs may: 

 

cause risk to people, environment and machine such as: 

 

risk to people due to non-secured work areas, 

 

failure of essential machine functions, 

 

failure of specified methods for the use, service and maintenance of the machine, 

 

risk to people due to mechanical and chemical effects, 

 

threat to the environment due to leaking operating media. 

 

lead to invalidation of any claims for damages. 

 
 
 
 
 
 
 
 
 
 
 
 

 

 

4 

Loading and unloading 

 

 

 

Observe the information in the chapter "Basic safety instructions", 

page 30. 

 

 

 

Loading and unloading by means of tractor 

 

 

WARNING 

 

Risk to people due to uncontrolled movements of the tractor and 

the machine if insufficient stability and insufficient steerability 

and braking ability of the tractor occur! 

 

Properly hitch the machine to the tractor before loading or 

unloading the machine onto or from a transport vehicle. 

 

When hitching and transporting the machine for loading and 

unloading, only use a tractor which meets the performance 

requirements and can safely slow down the machine.. 

 

  If the machine is equipped with a compressed-air brake system, 

you are only allowed to start moving the machine when the 

pressure gauge on the tractor indicates 5.0 bar. 

 

 

 

Summary of Contents for Super-Vitesse CFS 3101


































































































































































































































Reviews:

No comments