Strautmann Giga-Vitesse CFS 3602 Operating Instructions Manual Download Page 25

Page: 25 / 327

Product description

Giga-Vitesse CFS 3602 - 4402, Giga-Vitesse CFS 3602 DO - 4402 DO 03.18

2.5.3

Dual-line compressed-air brake system with hydraulic automatic load-
sensitive brake pressure (ALB) regulator

WARNING

Risk due to insufficient braking ability of the machine if the
travelling height of the hydraulic levelling system has not been
properly set!

The hydraulic levelling system properly triggers the ALB regulator
only with the travelling height properly set.

Tandem chassis

Fig. 7

(1)

Hose coupling with filter (feed line red)

(2)

Hose coupling with filter (brake line yellow)

(3)

Blank connection with fastening
mechanism

(4)

Release valve

(5)

Compressed-air reservoir

(6)

Drain valve

(7)

Trailer brake valve

(8)

Brake cylinder

(9)

Parking brake

(10) ALB regulator (hydraulic)

(11) Lines from the hydraulic cylinders of the

chassis

(12) Test connection

Summary of Contents for Giga-Vitesse CFS 3602








































































































































































































































































































































Search results

Summary of Contents for Giga-Vitesse CFS 3602

Reviews:

Related manuals for Giga-Vitesse CFS 3602

Brands by name

Popular brands

Strautmann Giga-Vitesse CFS 3602, Operating Instructions Manual

Search results

Summary of Contents for Giga-Vitesse CFS 3602

Reviews:

Related manuals for Giga-Vitesse CFS 3602

Brands by name

Popular brands