Strautmann Giga-Vitesse CFS 3602 Operating Instructions Manual Download Page 23 | Manualshive

Page: 23 / 327

background image

Product description

23

Giga-Vitesse CFS 3602 - 4402, Giga-Vitesse CFS 3602 DO - 4402 DO 03.18

2.5.1

Dual-line compressed-air brake system

The brake system consists of:



a braking axle with a dual-line compressed-air brake system and parking brake for an
admissible maximum speed of 25 km/h, 40 km/h or 60 km/h. The service brake acts on all tyres.



an automatic load-sensitive brake pressure regulator (ALB regulator). The ALB regulator
automatically controls the required braking force depending on the loading condition of the
hitched machine.

The brake system acts on the braking axle/s.

Observance of the maintenance intervals is indispensable for proper
functioning of the dual-line compressed-air brake system.

2.5.2

Dual-line compressed-air brake system with mechanical automatic load-
sensitive brake (ALB) regulator

WARNING

Risk due to insufficient braking ability of the machine if the
mechanical ALB regulator has not been properly set!

The setting dimension (L) at the ALB regulator must not be modified.
The setting dimension (L) must correspond to the value indicated on
the ALB plate.

«
...
21
22
23
24
25
...
»

Summary of Contents for Giga-Vitesse CFS 3602








































































































































































































































































































































Reviews:

No comments

Related manuals for Giga-Vitesse CFS 3602

Brand: Daavlin Pages: 13

Brand: Daavlin Pages: 27

Brand: Parker Pages: 54

Brand: Panasonic Pages: 174

Brand: DAKO Pages: 25

Brand: 3M ESPE Pages: 50

Brand: VACGEN Pages: 13

Brand: Paia Pages: 11

Brand: CAB Pages: 39

Brand: CAB Pages: 27

Brand: dbx Pages: 12

Brand: dbx Pages: 13

Brand: dbx Pages: 72

Brand: dbx Pages: 11

Brand: dbx Pages: 16

Brand: Gainsborough Pages: 2

Brand: Gainsborough Pages: 2

Brand: Gait up Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands