Stratus ftServer V 2302 Hardware Installation Manual Download Page 21

Page: 21 / 78

Removing the Packing Materials

Unpacking and Positioning the Cabinet

1-7

C A U T I O N

Use a pallet jack, not a forklift, to move the packaged
system. Using a forklift could damage the system. Use the
pallet jack at the front or rear of the cabinet.

3. Position the cabinet pallet so that it has the clearances shown in

Figure 1-3

Removing the Packing Materials

W A R N I N G

To avoid personal injury or damage to the system, two
persons are required to perform the following
procedures.

1. Orient the system package so that the package and the ramp have, as a minimum,

the clearance shown in

Figure 1-3

. Also, verify that you have enough clearance

above the system to remove the top cardboard cap.

2. With one person holding the ramp in place, use the metal shears to cut the exterior

shipping straps. To avoid injury while cutting each strap, hold the strap firmly with
one hand as you stand away from it. See

Figure 1-4

W A R N I N G

The shipping straps snap with considerable force
when they are cut! To avoid eye or skin injuries, use
caution when cutting the shipping straps.

Summary of Contents for ftServer V 2302















































































Search results

Summary of Contents for ftServer V 2302

Reviews:

Related manuals for ftServer V 2302

Brands by name

Popular brands

Stratus ftServer V 2302, Hardware Installation Manual

Search results

Summary of Contents for ftServer V 2302

Reviews:

Related manuals for ftServer V 2302

Brands by name

Popular brands