manualshive.com logo in svg

Strata CIX 200, Programming Manual

The "Strata CIX 200" General Description Manual is a comprehensive guide for users of this advanced telecommunication system. This manual provides in-depth information about its features, functions, and troubleshooting, enabling users to maximize the potential of their device. Download this manual for free from our website and become an expert user of Strata CIX 200. [Website]

Share
Download
background image

Services

Account Codes

Strata CIX Programming Vol.1    12/09

9-29

Ser

v

ices

570 Account Code Digit Length

Prerequisite Program:

None.

Accounting Codes need to be specified for the number of digits that are expected to be used for registering 
a number. This allows dialing within Strata CIX to proceed automatically once the correct account code is 
dialed. The following numbers are then dialed digits used for making the phone call.

A second length is provided to allow the number of digits to be used for verification of the code to be less 
than the total code entered, thus the code may contain two parts, one required and one part optional to the 
user.

F

IELD

D

ESCRIPTION

01 Verified Digit Length

The Verified Digit Length sets the number of leading digits within an 
account code to be verified against the table built in 506 Verified Account 
Codes. The Verified Digit Length may be shorter than, or as long as, the 
Registered Digit Length.

Note

This field is not changed, when 

“506 Verified Account Codes” 

on 

page 9-30

 are registered.

Possible values:4~15 (default = 4)

02 Registered Digit 

Length

The Registered Digit Length sets the number of digits in all account codes 
whether voluntary, forced and/or verified.

Note

The Registered Digit Length (field 02) must be greater than or 
equal to the Verified Digit Length (field 01).

Possible values:4~15 (default = 6)

03 Call Forward External 

Override FAC

Override Forced Account Code to allow Call Forwarding to an external 
destination. This applies to R2.22 MH233 and later software.

Possible values:Enable - Allows calls to a Forced Account Code station to 

forward without entering an Account Code.
Disable - Requires the caller to enter an Account Code 
before the call will forward. If a valid Account Code is not 
entered the call will disconnect.

Summary of Contents for CIX 200





























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CIX 200

2N LiftIP Manual preview
LiftIP
Brand: 2N Pages: 8
2N Lift1 Compact User Manual preview
Lift1 Compact
Brand: 2N Pages: 83
Hanlong UC860(P) User Manual preview
UC860(P)
Brand: Hanlong Pages: 68
Mio DigiWalker A701 User Manual preview
DigiWalker A701
Brand: Mio Pages: 168
ATCOM AT-620P Setup Manual preview
AT-620P
Brand: ATCOM Pages: 10
M4 SS4045 Quick Start Manual preview
SS4045
Brand: M4 Pages: 22
HTC PURE AT&T Safety And Regulatory Information Manual preview
PURE AT&T
Brand: HTC Pages: 16
Grandstream Networks GXP3000 User Manual preview
GXP3000
Brand: Grandstream Networks Pages: 56
Grandstream Networks GRP2603 Quick Installation Manual preview
GRP2603
Brand: Grandstream Networks Pages: 7
chinavasion CVXK-G419 User Manual preview
CVXK-G419
Brand: chinavasion Pages: 6
Garmin APPROACH G80 Quick Start Manual preview
APPROACH G80
Brand: Garmin Pages: 73
Mitel 3000 5330 Quick Reference User Manual preview
3000 5330
Brand: Mitel Pages: 29
Zte Z980L User Manual preview
Z980L
Brand: Zte Pages: 46
Zte Z987 User Manual preview
Z987
Brand: Zte Pages: 46
ACN IRIS X User Manual preview
IRIS X
Brand: ACN Pages: 51
Lava Spark 250 User Manual preview
Spark 250
Brand: Lava Pages: 31
Broadconnect IP Office 4602 Quick Reference Manual preview
IP Office 4602
Brand: Broadconnect Pages: 2
Siemens HiPath 500 Installation Operation & Maintenance preview
HiPath 500
Brand: Siemens Pages: 38

Brands by name

Popular brands

Load more brands