Strata CIX 200 Programming Manual Download Page 317 | Manualshive

Page: 317 / 508

background image

IP Telephone Programming

VLAN Setup

Strata CIX Programming Vol.1 12/09

8-3

IP T

e

le

phone

Pr
ogra

mming

VLAN Setup

The following steps setup the VLAN tagging options and parameters.

Using the VLAN Wizard

The wizard sets the VLAN parameters on the selected IP telephones. When complete, the MIPU, GIPU, or
LIPU/LIPS must be configured for VLAN.

In Network eManager select

IP-Telephony > IPT VLAN Setup

.

VLAN Range Options

The IP telephones to be setup can be selected by Primary Directory Number (PDN) or by the VLAN
Identification (VID) of either the PC Port or Phone Port.

•

Enter PDN Range

- Click on the

Select

button. This shows the list of IP PDNs - select one or more IP

telephones from the list.

•

Enter VID of target IP telephones

- enter either the IP telephone PC Port VID or Phone VID. This will

select every IP telephone with the specified port VID. If both PC Port and Phone Port VID is set to Any,
all IP telephones will be selected.

VLAN Setting Options

These options will set the selected IP telephones the parameters specified below or Resets the IP
telephones selected above to the default values.

•

Set VLAN settings of IP telephones

- Set the IP telephones selected above to the parameters

specified below.

•

Reset VLAN setting of IP telephones

- Reset the IP telephones selected above to the default value

(VLAN tagging disabled, VID = 1 for the phone port and the PC port).

VLAN Parameters

These options will set the selected IP telephones the parameters specified below or Resets the IP
telephones selected above to the default values.

•

VLAN Feature

- Enable or disable VLAN tagging for the selected IP telephones.

•

PC port type

- Set the PC port on the selected IP telephones to:

-

Trunk - the port is connected to a VLAN enabled device or

-

Access - the port is connected to a non-compliant device, a device that does not support VLAN
tagging.

Enable VLAN on the xIPU

This program sets the VLAN parameters on the GIPU/MIPU/LIPU cards. VLAN is enabled or disabled on a
per card basis. Refer to

“161 LIPU/MIPU/GIPU Configuration”

.

Setup the Packet Prioritization (IEEE802.1P) and VLAN ID (IEEE802.1Q).

«
...
315
316
317
318
319
...
»

Summary of Contents for CIX 200





























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CIX 200

Brand: 2N Pages: 32

Brand: Samsung Pages: 343

Brand: Sony Ericsson Pages: 30

Brand: Pantech Pages: 143

Brand: Blackberry Pages: 4

Brand: Koncept Pages: 12

Brand: SoftBank Pages: 2

Brand: Pharos Pages: 104

Brand: switel Pages: 4

Brand: Samsung Pages: 151

Brand: Samsung Pages: 222

Brand: Samsung Pages: 151

Brand: Samsung Pages: 109

Brand: Tobii Dynavox Pages: 26

Brand: iPRIMUS Pages: 2

Brand: Alcatel Pages: 40

Brand: Fanvil Pages: 11

Mediamaster 210

Brand: Nokia Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands