manualshive.com logo in svg

Strata CIX 200, Programming Manual

The "Strata CIX 200" General Description Manual is a comprehensive guide for users of this advanced telecommunication system. This manual provides in-depth information about its features, functions, and troubleshooting, enabling users to maximize the potential of their device. Download this manual for free from our website and become an expert user of Strata CIX 200. [Website]

Share
Download
background image

Strata CIX Programming Vol.1    12/09

8-1

IP T

e

leph

on
e 

Progra

mming

IP Telephone Programming

8

IP Telephone Setup

This chapter contains information on system setup for IP telephones, IP telephone programming, IP 
interface card and IP software updates.

CIX IP Telephone Programming

The following is an outline of the Basic CIX system IP setup. This process covers the basic IP telephone 
programming. Each network is unique and may require additional special assignments.

Card Assignments

System > Card Assignment

— Assign the xIPU IP card; refer to the program guidelines for appropriate 

slot assignments.

MIPU, GIPU, and LIPU Configuration

IP-Telephony > L/M/G IPU Configuration

 — Assign the xIPU IP Address, subnet mask and gateway. 

BIPU Configuration

IP-Telephony > BIPU Configuration

 — Assign the BIPU-M IP Address, subnet mask and gateway.

Station Programming

Assigning PDNs to IP telephones using IP resources

 — This can be completed by using the Network 

eManager PDN Range wizard or manually created, 

IP-Telephony > IPT Data 

—

 

Program 200 (station 

basic).

•

IP telephones assigned to xIPU-M cards are programmed in the same manner as DKTs. Any 
programmed (FB) used to program a DKT can be used to program an IP.

•

Continue station programming in the same manner as a DKT set, including:

-

DKT Parameters

-

Key  Strips

Cabinet/Slot

Select the GIPU/MIPU/LIPU card from the list

field 01

Enter the GIPU/MIPU/LIPU IP Address (default = 192.168.254.200)

field 02

Enter the GIPU/MIPU/LIPU Subnet Address

field 03

Enter the GIPU/MIPU/LIPU Default Gateway Address

Summary of Contents for CIX 200





























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CIX 200

Rath 2100 Series Installation & Operation Manual preview
2100 Series
Brand: Rath Pages: 6
Rath 2100 Series Operation Manual preview
2100 Series
Brand: Rath Pages: 6
United Security Products 10-4 Owner'S Manual And Operating Instructions preview
10-4
Brand: United Security Products Pages: 24
Yealink Yealink SIP-T48G Quick User Manual preview
Yealink SIP-T48G
Brand: Yealink Pages: 2
Yealink Yealink SIP-T48G Quick Reference User Manual preview
Yealink SIP-T48G
Brand: Yealink Pages: 4
Yealink Yealink SIP-T46G Quick Start Manual preview
Yealink SIP-T46G
Brand: Yealink Pages: 38
Yealink One Talk CP960 User Manual preview
One Talk CP960
Brand: Yealink Pages: 255
Yealink Yealink SIP-T48G User Manual preview
Yealink SIP-T48G
Brand: Yealink Pages: 105
Yealink T48G Complete Overview preview
T48G
Brand: Yealink Pages: 13
Yealink CP860 SERIES Configuring Manual preview
CP860 SERIES
Brand: Yealink Pages: 77
HTC 2PS6400 Safety Manual preview
2PS6400
Brand: HTC Pages: 12
Archos Access 50S Quick Start Manual preview
Access 50S
Brand: Archos Pages: 45
T-Mobile REVVL 5G User Manual preview
REVVL 5G
Brand: T-Mobile Pages: 29
Alcatel One Touch 525 User Manual preview
One Touch 525
Brand: Alcatel Pages: 48
LOGICOM M bot 52 Quick Start Manual preview
M bot 52
Brand: LOGICOM Pages: 13
ZTC ZT6588 User Manual preview
ZT6588
Brand: ZTC Pages: 169
BTECH BGM-1010 User Manual preview
BGM-1010
Brand: BTECH Pages: 60
Tesla SimplePhone A50 Manual preview
SimplePhone A50
Brand: Tesla Pages: 32

Brands by name

Popular brands

Load more brands